// Support · XPEL manufacturer warranties

YOUR WARRANTY.

XPEL’s warranty terms for the films and coatings we install. Find your product to read them.

18 products · Terms current as of Sep 2026 · Source: XPEL

// Something wrong?

MAKE A CLAIM.

Start a claim

Tell us what you’re seeing. Have your warranty card, your receipt showing the covered areas, and photos if you can.

WE FILE IT WITH XPEL

We inspect it and send XPEL a written claim. No repair work starts until XPEL approves the plan.

WE MAKE IT RIGHT

Once XPEL approves the claim, we do the approved work.

// 01 · XPEL PAINT PROTECTION FILM

PAINT PROTECTION FILM.

Product · What’s covered

Coverage

Transfer

Annual check

Terms

01 //

ULTIMATE FUSION

Yellowing, cracking, blistering, and delaminating. Additional defects (4 yrs): oxidation, loss of gloss, UV damage, fading.

10 YRS

+ 4 yrs additional defects

Transfer:

YES

Annual check:

REQUIRED

XPEL PDF ↗

Limited Product Warranty

ULTIMATE FUSION PPF

XPEL, Inc. (the “Company”) expressly warrants to the owner that, for a period of ten (10) years (the “Warranty Period”) from the date of initial installation, the Company will cover defects on ULTIMATE FUSION (the “Product(s)”) such as: yellowing, cracking, blistering, and delaminating. This Limited Warranty only applies to the Company’s Products which are professionally installed in the manner recommended by the Company.

In addition to the terms above, the Company expressly warrants to the owner that, for a period of four (4) years (the “Warranty Period”) from the date of initial installation. The Company will cover additional defects on the ULTIMATE FUSION (the “Product(s)”) such as: oxidation, loss of gloss, UV damage, fading. This Limited Warranty only applies to the Company’s Products which are professionally installed in the manner recommended by the Company.

The Company will, at its option, remove or replace the Product without charge if the Product fails or does not perform as warranted solely due to a manufacturing defect within the Warranty Period, subject to the exclusions set forth in this Limited Warranty. If the Company elects to replace the Product, the Company will have an authorized installer of its choice remove and reapply the Product to areas determined by the Company in its sole discretion to be covered by this Limited Warranty. The Company will cover parts and labor. The replacement of the defective film is the exclusive remedy for all Products covered under this Limited Warranty. During the entire Warranty Period, the Company’s obligation as to repair or replacement shall further be limited to repair or replacement with the Products that are available at the time of the repair or replacement, shall be limited to the repair or replacement of only the specific Product that fails due to a manufacturing defect. Any repaired or replaced product shall also remain subject to the Warranty Period, and any repair or replacement shall not extend the original Warranty Period in any manner or start a new warranty period. These are the exclusive remedies for all Products covered under this Limited Warranty.

You may obtain coverage under this Limited Warranty by providing Company with proof of warranty card, copy of original receipt for the Product identifying coverage areas, along with a detailed description of the purported defect. For service under this Limited Warranty, you must notify the authorized Company installer who performed the installation of the Product, in writing, providing claimant’s name, phone number, address, and the installation address (if different), a description of the product involved and the nature of the defect.

This Limited Warranty is transferable only when the new owner submits to the Company proof of the original date of installation. Transfer of the Limited Warranty only entitles the new owner coverage for the remainder of the original Warranty Period.

Disclaimer Of Warranties

The Company’s Products must be stored, handled, installed, used, and maintained in accordance with instructions provided by the Company, and this Limited Warranty is conditioned upon compliance with all such instructions. Copies of the Company’s guides are available from the Company at the address listed below. You may also obtain this/these materials by contacting Company at +1 (210) 678-3700 or on the Company’s website at www.xpel.com.

XPEL Paint Protection films are an effective sacrificial layer, providing robust paint protection.

This Limited Warranty does not cover defects caused by:

1. Non-compliance with the Company’s guide or instructions. Such failures include, but are not limited to, exposure to physical abuse, including, but not limited to chemical abuse (e.g. harsh cleansers and solvents), thermal abuse or shock (e.g. excessive heat or cold) or misuse;
2. Improper storage, installation, handling and/or use of the Product;
3. Damage not resulting from manufacturing defects that occur while the Product is in the customer’s possession;
4. Unreasonable or unintended use of Product;
5. Products installed with known or visible manufacturing defects at the time of installation, including, but not limited to scratches, scuffs, scrapes, chips to the painted surface;
6. Stains, and scratches;
7. Damage to the wrapped surface due to improper wash techniques, automatic car washes or incorrect wash tools that may cause abrasion or by third parties not authorized by the Company;
8. Scratches, scuffs, scrapes, chips to the painted surface;
9. Water spots – water spots are caused by mineral deposits, which if left to dry on the paint protection film may leave a stain, water spots are not covered;
10. Damage caused by collision, accidental damage, vandalism, fire, hail, flood, surface rust, rail dust, physical damage, paint overspray, or paint manufacturer’ defects, which may be covered under manufactures protection plan; and
11. Use in non-automotive applications;
12. Use of non-XPEL branded ceramic coatings;
13. Damages caused by outside forces, including the physical impact of rocks or road debris.

Any information or suggestion by the Company with respect to the Products concerning applications, specifications or compliance with codes and standards is provided solely for your convenient reference and are made without any representation as to accuracy or suitability. You must verify and test the suitability of any information with respect to the Products for your specific application.

THE WARRANTIES SET FORTH HEREIN ARE THE ONLY WARRANTIES MADE BY THE COMPANY IN CONNECTION WITH THESE PRODUCTS. THE COMPANY CANNOT AND DOES NOT MAKE ANY IMPLIED OR EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, AND DISCLAIMS ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PRODUCTS SOLD BY COMPANY ARE SOLD ONLY TO THE SPECIFICATIONS SPECIFICALLY SET FORTH BY COMPANY IN WRITING. OTHER THAN THE LIMITED WARRANTY SET FORTH HEREIN, THE COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY’S SOLE OBLIGATION UNDER THIS WARRANTY SHALL BE REPAIR OR REPLACEMENT OF NON-CONFORMING PRODUCTS, OR AT THE OPTION OF THE COMPANY, RETURN OF THE PRODUCT AND A REFUND OF THE PURCHASE PRICE. BUYER ASSUMES ALL RISK WHATSOEVER AS TO THE RESULT OF THE USE OF THE PRODUCTS PURCHASED, WHETHER USED SINGULARLY OR IN COMBINATION WITH ANY OTHER PRODUCTS OR SUBSTANCES.

Limitation Of Liability

NO CLAIM BY THE BUYER/OWNER OF ANY KIND, INCLUDING CLAIMS FOR INDEMNIFICATION, SHALL BE GREATER IN AMOUNT THAN THE PURCHASE PRICE OF THE PRODUCTS IN RESPECT TO WHICH DAMAGES ARE CLAIMED. IN NO EVENT SHALL THE COMPANY BE LIABLE TO BUYER/OWNER IN TORT, CONTRACT OR OTHERWISE, FOR ANY SPECIAL, INDIRECT, INCIDENTAL, CONSEQUENTIAL, RELIANCE, STATUTORY, SPECIAL, PUNITIVE OR EXEMPLARY DAMAGES, INCLUDING, BUT NOT LIMITED TO, LOST PROFITS, LOSS OF USE, LOSS OF TIME, LOSS OF REVENUES, INCONVENIENCE, LOSS BUSINESS OPPORTUNITIES, DAMAGE TO GOOD WILL OR REPUTATION, OR LOSS OF DATA, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR SUCH DAMAGES COULD HAVE BEEN REASONABLY FORESEEN, IN CONNECTION WITH, ARISING OUT OF, OR AS A RESULT OF, THE SALE, DELIVERY, SERVICING, USE OR LOSS OF USE OF THE PRODUCTS SOLD HEREUNDER, OR FOR ANY LIABILITY OF BUYER TO ANY THIRD PARTY WITH RESPECT THERETO.

Annual Inspections

To maintain the warranty on your product, an annual inspection is required throughout the warranty period, as stated in the product specifications. This inspection should be performed by an XPEL certified Fusion Installer every year and must be completed within 30 days before or after the anniversary date of installation or the date of any previous inspection or service. Failure to complete the inspection, within the required time will void the Limited Warranty. Any fees or charges by the XPEL Certified Installer will be charged to the owner to do the annual inspection including, but not limited to, exterior wash, decontamination, and inspection. Please keep proof of all inspections, as they must be provided if you have a Limited Warranty related issue.

Contact Information

Any questions concerning this Limited Warranty should be addressed to:

XPEL, Inc.
Address: 711 Broadway St., Ste. 320, San Antonio, TX 78215
Attention: Warranty Department
Phone: (800) 447-9928
Website address: www.xpel.com
Email address: xpelwarranty@xpel.com

02 //

ULTIMATE PLUS

Yellowing, cracking, blistering, and delaminating.

10 YRS

from install date

Transfer:

YES

Annual check:

NOT NEEDED

XPEL PDF ↗

Limited Product Warranty

ULTIMATE PLUS & STEALTH PPF

XPEL, Inc. (the “Company”) expressly warrants to the owner that, for a period of ten (10) years (the “Warranty Period”) from the date of initial installation. The Company will cover defects on the ULTIMATE PLUS & STEALTH (the “Product(s)”) such as: yellowing, cracking, blistering, and delaminating. This Limited Warranty only applies to the Company’s Products which are professionally installed in the manner recommended by the Company.

The Company will, at its option, remove or replace the Product without charge if the Product fails or does not perform as warranted solely due to a manufacturing defect within the Warranty Period, subject to the exclusions set forth in this Limited Warranty. If the Company elects to replace the Product, the Company will have an authorized installer of its choice remove and reapply the Product to areas determined by the Company in its sole discretion to be covered by this Limited Warranty. The Company will cover parts and labor. The replacement of the defective film is the exclusive remedy for all Products covered under this Limited Warranty. During the entire Warranty Period, the Company’s obligation as to repair or replacement shall further be limited to repair or replacement with the Products that are available at the time of the repair or replacement, shall be limited to the repair or replacement of only the specific Product that fails due to a manufacturing defect. Any repaired or replaced product shall also remain subject to the Warranty Period, and any repair or replacement shall not extend the original Warranty Period in any manner or start a new warranty period. These are the exclusive remedies for all Products covered under this Limited Warranty.

You may obtain coverage under this Limited Warranty by providing Company with proof of warranty card, copy of original receipt for the Product identifying coverage areas, along with a detailed description of the purported defect. For service under this Limited Warranty, you must notify the authorized Company installer who performed the installation of the Product, in writing, providing claimant’s name, phone number, address, and the installation address (if different), a description of the product involved and the nature of the defect.

This Limited Warranty is transferable only when the new owner submits to the Company proof of the original date of installation. Transfer of the Limited Warranty only entitles the new owner coverage for the remainder of the original Warranty Period.

Disclaimer Of Warranties

The Company’s Products must be stored, handled, installed, used, and maintained in accordance with instructions provided by the Company, and this Limited Warranty is conditioned upon compliance with all such instructions. Copies of the Company’s guides are available from the Company at the address listed below. You may also obtain this/these materials by contacting Company at +1 (210) 678-3700 or on the Company’s website at www.xpel.com.

XPEL Paint Protection films are an effective sacrificial layer, providing robust paint protection.

This Limited Warranty does not cover defects caused by:

1. Non-compliance with the Company’s guide or instructions. Such failures include, but are not limited to, exposure to physical abuse, including, but not limited to chemical abuse (e.g. harsh cleansers and solvents), thermal abuse or shock (e.g. excessive heat or cold) or misuse;
2. Improper storage, installation, handling and/or use of the Product;
3. Damage not resulting from manufacturing defects that occur while the Product is in the customer’s possession;
4. Unreasonable or unintended use of Product;
5. Products installed with known or visible manufacturing defects at the time of installation, including, but not limited to scratches, scuffs, scrapes, chips to the painted surface;
6. Stains, and scratches;
7. Damage to the wrapped surface due to improper wash techniques, automatic car washes or incorrect wash tools that may cause abrasion or by third parties not authorized by the Company;
8. Scratches, scuffs, scrapes, chips to the painted surface;
9. Water spots – water spots are caused by mineral deposits, which if left to dry on the paint protection film may leave a stain, water spots are not covered;
10. Damage caused by collision, accidental damage, vandalism, fire, hail, flood, surface rust, rail dust, physical damage, paint overspray, or paint manufacturer’ defects, which may be covered under manufactures protection plan;
11. Areas that have not been re-wrapped after a paint or body repair;
12. Use in non-automotive applications.
13. Use of non-XPEL branded ceramic coatings;
14. Damages caused by outside forces, including the physical impact of rocks or road debris.

Any information or suggestion by the Company with respect to the Products concerning applications, specifications or compliance with codes and standards is provided solely for your convenient reference and are made without any representation as to accuracy or suitability. You must verify and test the suitability of any information with respect to the Products for your specific application.

THE WARRANTIES SET FORTH HEREIN ARE THE ONLY WARRANTIES MADE BY THE COMPANY IN CONNECTION WITH THESE PRODUCTS. THE COMPANY CANNOT AND DOES NOT MAKE ANY IMPLIED OR EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, AND DISCLAIMS ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PRODUCTS SOLD BY COMPANY ARE SOLD ONLY TO THE SPECIFICATIONS SPECIFICALLY SET FORTH BY COMPANY IN WRITING. OTHER THAN THE LIMITED WARRANTY SET FORTH HEREIN, THE COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY’S SOLE OBLIGATION UNDER THIS WARRANTY SHALL BE REPAIR OR REPLACEMENT OF NON-CONFORMING PRODUCTS, OR AT THE OPTION OF THE COMPANY, RETURN OF THE PRODUCT AND A REFUND OF THE PURCHASE PRICE. BUYER ASSUMES ALL RISK WHATSOEVER AS TO THE RESULT OF THE USE OF THE PRODUCTS PURCHASED, WHETHER USED SINGULARLY OR IN COMBINATION WITH ANY OTHER PRODUCTS OR SUBSTANCES.

Limitation Of Liability

Contact Information

03 //

STEALTH

Yellowing, cracking, blistering, and delaminating.

10 YRS

from install date

Transfer:

YES

Annual check:

NOT NEEDED

XPEL PDF ↗

Limited Product Warranty

ULTIMATE PLUS & STEALTH PPF

Disclaimer Of Warranties

The Company’s Products must be stored, handled, installed, used, and maintained in accordance with instructions provided by the Company, and this Limited Warranty is conditioned upon compliance with all such instructions. Copies of the Company’s guides are available from the Company at the address listed below. You may also obtain this/these materials by contacting Company at +1 (210) 678-3700 or on the Company’s website at www.xpel.com.

XPEL Paint Protection films are an effective sacrificial layer, providing robust paint protection.

This Limited Warranty does not cover defects caused by:

1. Non-compliance with the Company’s guide or instructions. Such failures include, but are not limited to, exposure to physical abuse, including, but not limited to chemical abuse (e.g. harsh cleansers and solvents), thermal abuse or shock (e.g. excessive heat or cold) or misuse;
2. Improper storage, installation, handling and/or use of the Product;
3. Damage not resulting from manufacturing defects that occur while the Product is in the customer’s possession;
4. Unreasonable or unintended use of Product;
5. Products installed with known or visible manufacturing defects at the time of installation, including, but not limited to scratches, scuffs, scrapes, chips to the painted surface;
6. Stains, and scratches;
7. Damage to the wrapped surface due to improper wash techniques, automatic car washes or incorrect wash tools that may cause abrasion or by third parties not authorized by the Company;
8. Scratches, scuffs, scrapes, chips to the painted surface;
9. Water spots – water spots are caused by mineral deposits, which if left to dry on the paint protection film may leave a stain, water spots are not covered;
10. Damage caused by collision, accidental damage, vandalism, fire, hail, flood, surface rust, rail dust, physical damage, paint overspray, or paint manufacturer’ defects, which may be covered under manufactures protection plan;
11. Areas that have not been re-wrapped after a paint or body repair;
12. Use in non-automotive applications.
13. Use of non-XPEL branded ceramic coatings;
14. Damages caused by outside forces, including the physical impact of rocks or road debris.

Any information or suggestion by the Company with respect to the Products concerning applications, specifications or compliance with codes and standards is provided solely for your convenient reference and are made without any representation as to accuracy or suitability. You must verify and test the suitability of any information with respect to the Products for your specific application.

THE WARRANTIES SET FORTH HEREIN ARE THE ONLY WARRANTIES MADE BY THE COMPANY IN CONNECTION WITH THESE PRODUCTS. THE COMPANY CANNOT AND DOES NOT MAKE ANY IMPLIED OR EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, AND DISCLAIMS ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PRODUCTS SOLD BY COMPANY ARE SOLD ONLY TO THE SPECIFICATIONS SPECIFICALLY SET FORTH BY COMPANY IN WRITING. OTHER THAN THE LIMITED WARRANTY SET FORTH HEREIN, THE COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY’S SOLE OBLIGATION UNDER THIS WARRANTY SHALL BE REPAIR OR REPLACEMENT OF NON-CONFORMING PRODUCTS, OR AT THE OPTION OF THE COMPANY, RETURN OF THE PRODUCT AND A REFUND OF THE PURCHASE PRICE. BUYER ASSUMES ALL RISK WHATSOEVER AS TO THE RESULT OF THE USE OF THE PRODUCTS PURCHASED, WHETHER USED SINGULARLY OR IN COMBINATION WITH ANY OTHER PRODUCTS OR SUBSTANCES.

Limitation Of Liability

Contact Information

04 //

COLOR PPF

Yellowing, cracking, blistering, and delaminating.

10 YRS

from install date

Transfer:

Annual check:

NOT NEEDED

XPEL terms ↗

Limited Product Warranty

COLOR PPF

XPEL, Inc. (the “Company”) expressly warrants to the owner that, for a period of ten (10) years (the “Warranty Period”) from the date of initial installation. The Company will cover defects on the XPEL COLOR PPF (the “Product(s)”) such as: yellowing, cracking, blistering, and delaminating. This Limited Warranty only applies to the Company’s Products which are professionally installed in the manner recommended by the Company.

The Company will, at its option, remove or replace the Product without charge if the Product fails or does not perform as warranted solely due to a manufacturing defect within the Warranty Period, subject to the exclusions set forth in this Limited Warranty. If the Company elects to replace the Product, the Company will have an authorized installer of its choice remove and reapply the Product to areas determined by the Company in its sole discretion to be covered by this Limited Warranty. The Company will cover parts and labor. The replacement of the defective film is the exclusive remedy for all Products covered under this Limited Warranty. During the entire Warranty Period, the Company’s obligation as to repair or replacement shall further be limited to repair or replacement with the Products that are available at the time of the repair or replacement, shall be limited to the repair or replacement of only the specific Product that fails due to a manufacturing defect. Any repaired or replaced product shall also remain subject to the Warranty Period, and any repair or replacement shall not extend the original Warranty Period in any manner or start a new warranty period. These are the exclusive remedies for all Products covered under this Limited Warranty.

You may obtain coverage under this Limited Warranty by providing Company with proof of warranty card, copy of original receipt for the Product identifying coverage areas, along with a detailed description of the purported defect. For service under this Limited Warranty, you must notify the authorized Company installer who performed the installation of the Product, in writing, providing claimant’s name, phone number, address, and the installation address (if different), a description of the product involved and the nature of the defect.

This Limited Warranty is non-transferable.

Disclaimer Of Warranties

The Company’s Products must be stored, handled, installed, used, and maintained in accordance with instructions provided by the Company, and this Limited Warranty is conditioned upon compliance with all such instructions. Copies of the Company’s guides are available from the Company at the address listed below. You may also obtain this/these materials by contacting Company at +1 (210) 678-3700 or on the Company’s website at www.xpel.com.

XPEL Paint Protection films are an effective sacrificial layer, providing robust paint protection.

This Limited Warranty does not cover defects caused by:

1. Non-compliance with the Company’s guide or instructions. Such failures include, but are not limited to, exposure to physical abuse, including, but not limited to chemical abuse (e.g. harsh cleansers and solvents), thermal abuse or shock (e.g. excessive heat or cold) or misuse;
2. Improper storage, installation, handling and/or use of the Product;
3. Damage not resulting from manufacturing defects that occur while the Product is in the customer’s possession;
4. Unreasonable or unintended use of Product;
5. Products installed with known or visible manufacturing defects at the time of installation, including, but not limited to scratches, scuffs, scrapes, chips to the painted surface;
6. Stains, and scratches;
7. Damage to the wrapped surface due to improper wash techniques, automatic car washes or incorrect wash tools that may cause abrasion or by third parties not authorized by the Company;
8. Scratches, scuffs, scrapes, chips to the painted surface;
9. Water spots – water spots are caused by mineral deposits, which if left to dry on the paint protection film may leave a stain, water spots are not covered;
10. Damage caused by collision, accidental damage, vandalism, fire, hail, flood, surface rust, rail dust, physical damage, paint overspray, or paint manufacturer’ defects, which may be covered under manufactures protection plan;
11. Areas that have not been re-wrapped after a paint or body repair;
12. Use in non-automotive applications.
13. Use of non-XPEL branded ceramic coatings;
14. Damages caused by outside forces, including the physical impact of rocks or road debris.

Any information or suggestion by the Company with respect to the Products concerning applications, specifications or compliance with codes and standards is provided solely for your convenient reference and are made without any representation as to accuracy or suitability. You must verify and test the suitability of any information with respect to the Products for your specific application.

THE WARRANTIES SET FORTH HEREIN ARE THE ONLY WARRANTIES MADE BY THE COMPANY IN CONNECTION WITH THESE PRODUCTS. THE COMPANY CANNOT AND DOES NOT MAKE ANY IMPLIED OR EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, AND DISCLAIMS ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PRODUCTS SOLD BY COMPANY ARE SOLD ONLY TO THE SPECIFICATIONS SPECIFICALLY SET FORTH BY COMPANY IN WRITING. OTHER THAN THE LIMITED WARRANTY SET FORTH HEREIN, THE COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY’S SOLE OBLIGATION UNDER THIS WARRANTY SHALL BE REPAIR OR REPLACEMENT OF NON-CONFORMING PRODUCTS, OR AT THE OPTION OF THE COMPANY, RETURN OF THE PRODUCT AND A REFUND OF THE PURCHASE PRICE. BUYER ASSUMES ALL RISK WHATSOEVER AS TO THE RESULT OF THE USE OF THE PRODUCTS PURCHASED, WHETHER USED SINGULARLY OR IN COMBINATION WITH ANY OTHER PRODUCTS OR SUBSTANCES.

Limitation Of Liability

Contact Information

// 02 · XPEL PRIME · VISION

WINDOW FILM.

Product · What’s covered

Coverage

Transfer

Annual check

Terms

01 //

PRIME XR PLUS · PRIME XR

Discoloration, fading, bubbling, peeling, cracking, and delamination.

LIFETIME

of the vehicle

Transfer:

YES

Annual check:

NOT NEEDED

XPEL PDF ↗

Limited Product Warranty

PRIME™ Automotive Window Film

XPEL, Inc. (the “Company”) expressly warrants to the owner that, for the life of your vehicle (the “Warranty Period”) from the date of initial installation. The Company will cover defects on the PRIME Automotive Window Film (the “Product(s)”) such as: discoloration, fading, bubbling, peeling, cracking, and delamination. This Limited Warranty only applies to the Company’s Products which are professionally installed in the manner recommended by the Company.

The Company will, at its option, remove or replace the Product without charge if the Product fails or does not perform as warranted solely due to a manufacturing defect within the Warranty Period, subject to the exclusions set forth in this Limited Warranty. If the Company elects to replace the Product, the Company will have an authorized installer of its choice remove and reapply the Product to areas determined by the Company in its sole discretion to be covered by this Limited Warranty. The Company will cover parts and labor. The replacement of the defective film is the exclusive remedy for all Products covered under this Limited Warranty. During the entire Warranty Period, the Company’s obligation as to repair or replacement shall further be limited to repair or replacement with the Products that are available at the time of the repair or replacement, shall be limited to the repair or replacement of only the specific Product that fails due to a manufacturing defect. Any repaired or replaced product shall also remain subject to the Warranty Period, and any repair or replacement shall not extend the original Warranty Period in any manner or start a new warranty period. These are the exclusive remedies for all Products covered under this Limited Warranty.

You may obtain coverage under this Limited Warranty by providing Company with proof of warranty card, copy of original receipt for the Product identifying coverage areas, along with a detailed description of the purported defect. For service under this Limited Warranty, you must notify the authorized Company installer who performed the installation of the Product, in writing, providing claimant’s name, phone number, address, and the installation address (if different), a description of the product involved and the nature of the defect.

This Limited Warranty is transferable only when the new owner submits to the Company proof of the original date of installation. Transfer of the Limited Warranty only entitles the new owner coverage for the remainder of the original Warranty Period.

Disclaimer Of Warranties

The Company’s Products must be stored, handled, installed, used, and maintained in accordance with instructions provided by the Company, and this Limited Warranty is conditioned upon compliance with all such instructions. Copies of the Company’s guides are available from the Company at the address listed below. You may also obtain this/these materials by contacting Company at +1 (210) 678-3700 or on the Company’s website at www.xpel.com.

This Limited Warranty does not cover defects caused by:

1. Non-compliance with the Company’s guide or instructions. Such failures include, but are not limited to, exposure to physical abuse, including, but not limited to chemical abuse (e.g., harsh cleansers and solvents), thermal abuse or shock (e.g., excessive heat or cold) or misuse;
2. Improper storage, installation, handling and/or use of the Product;
3. Damage not resulting from manufacturing defects that occur while the Product is in the customer’s possession;
4. Unreasonable or unintended use of Product;
5. Products installed with known or visible manufacturing defects at the time of installation, including, but not limited to scratches, scuffs, scrapes, chips to the tinted surface;
6. Stains, and scratches;
7. Damage to the tinted surface due to improper wash techniques, automatic car washes or incorrect wash tools that may cause abrasion or by third parties not authorized by the Company;
8. Scratches, scuffs, scrapes, chips to the tinted surface;
9. Damage caused by collision, accidental damage, vandalism, fire, hail, flood, surface rust, rail dust, physical damage, paint overspray, or glass manufacturer’ defects, which may be covered under manufactures protection plan;
10. Use in non-automotive applications.

Any information or suggestion by the Company with respect to the Products concerning applications, specifications or compliance with codes and standards is provided solely for your convenient reference and are made without any representation as to accuracy or suitability. You must verify and test the suitability of any information with respect to the Products for your specific application.

THE WARRANTIES SET FORTH HEREIN ARE THE ONLY WARRANTIES MADE BY THE COMPANY IN CONNECTION WITH THESE PRODUCTS. THE COMPANY CANNOT AND DOES NOT MAKE ANY IMPLIED OR EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, AND DISCLAIMS ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PRODUCTS SOLD BY COMPANY ARE SOLD ONLY TO THE SPECIFICATIONS SPECIFICALLY SET FORTH BY COMPANY IN WRITING. OTHER THAN THE LIMITED WARRANTY SET FORTH HEREIN, THE COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY’S SOLE OBLIGATION UNDER THIS WARRANTY SHALL BE REPAIR OR REPLACEMENT OF NON-CONFORMING PRODUCTS, OR AT THE OPTION OF THE COMPANY, RETURN OF THE PRODUCT AND A REFUND OF THE PURCHASE PRICE. BUYER ASSUMES ALL RISK WHATSOEVER AS TO THE RESULT OF THE USE OF THE PRODUCTS PURCHASED, WHETHER USED SINGULARLY OR IN COMBINATION WITH ANY OTHER PRODUCTS OR SUBSTANCES.

Limitation Of Liability

Contact Information

02 //

VISION HOME & OFFICE

Peeling, bubbling, rippling, cracking, adhesive failure, delamination, and demetalization.

UP TO 15 YRS

limited lifetime residential

Transfer:

Annual check:

NOT NEEDED

XPEL PDF ↗

WARRANTY INFORMATION

IMPORTANT: Read this entire Limited Warranty (not transferable), before purchasing or installing XPEL® brand commercial and residential window films. By installing or using XPEL Technologies Corp. (“XPEL”) VISION window films, you acknowledge that this Limited Warranty is part of the terms of sale.

WARRANTY COVERAGE

XPEL warrants professionally sold and installed XPEL® VISION brand commercial and residential window films (the “Products”) to be free from the following. Defects in materials and workmanship: peeling, bubbling, rippling, cracking, adhesive failure, delamination, and demetalization. XPEL does not warrant any conditions of, or damage to, the Products other than the conditions described in this Limited Warranty. Warranty time periods vary and are stated on the schedule on the back of this Limited Warranty. PLEASE NOTE IMPORTANT EXCLUSIONS AND PRE-APPROVAL REQUIREMENTS SPECIFIED ON THE REVERSE SIDE OF THIS DOCUMENT.

GLASS BREAKAGE WARRANTY

Except with respect to the exclusion provided below, this Limited Warranty on the Products covers glass breakage due to thermal stress. XPEL reserves the right to have a local representative of its choice inspect the affected window(s) before approving claims. Upon approval of a claim at XPEL’s sole discretion, XPEL will pay for glass unit replacement up to a maximum of $500 per window.

SEAL FAILURE ON DUAL-PANE UNITS

Except with respect to the exclusion provided below, this Limited Warranty extends to seal failure on dual pane units, if and only if the customer has and provides to XPEL a window manufacturer’s warranty against seal failure that is valid and not expired, at the time of claim. XPEL reserves the right to have a local representative of its choice inspect the affected window(s) before approving any claim. For approved claims, XPEL only warrants against seal failure for the remaining period of the window manufacturer’s warranty, or the time period noted on the reverse side, whichever is shorter. Upon approval of a claim at XPEL’s sole discretion, XPEL will pay for glass unit replacement up to a maximum of $500 per window.

EXCLUSIONS; XPEL’S OPTION TO REMOVE FILM

This Limited Warranty does not extend to damage caused by improper Product installation, improper Product application, improper Product care, cleaning or maintenance, abnormal conditions, abuse, misuse, normal wear and tear, accidents, intentional damage of any kind, improper or unauthorized repairs, or any other acts or defects not related solely to defects in materials or workmanship. Buildings with any prior history of seal failure or thermal glass breakage are not eligible for glass breakage or seal failure coverage. Further, in the event of multiple failures on one or more filmed windows, XPEL reserves the right to remove all XPEL window film and reimburse the customer only the amount of the original film installation.

GENERAL PROVISIONS

This Limited Warranty is offered only to the original purchaser at the time of Product installation. This Limited Warranty may not be transferred, sold or assigned. Rental units are considered commercial properties. This Limited Warranty terminates automatically upon any sale, conveyance or change in tenancy of any property. For valid warranty claims, XPEL will have an authorized XPEL installer of its choice remove and reapply the Product to areas determined by XPEL in its sole discretion to be covered by this Limited Warranty, and XPEL will cover parts and labor. The replacement of the defective film, including parts and labor, is the exclusive remedy for all Products covered under this Limited Warranty. Payment for labor charges covered by this Limited Warranty will be made directly to the authorized XPEL installer and will be calculated by using the coverage allowance published by XPEL.

WARRANTY DISCLAIMER

There are no warranties which extend beyond the description on the face hereof, nor are there warranties of fitness for a particular purpose or merchantability applicable to the products. This manufacturer’s warranty does not cover custom products, improper or poor installation of the products which include but is not limited to, squeegeeing, trimming and measuring. In no event shall the manufacturer be liable or responsible for any loss or damage including, without limitation, direct, indirect or consequential damages, except as expressly set forth herein. This limited warranty is made in lieu of all warranties, expressed or implied, and is void if the product has been subject to abuse, improper installation and/or care. This warranty gives you specific legal rights and you may also have other rights which vary by state or province.

WARRANTY DISCLAIMER; APPLICATION OF LAW

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF, NOR ARE THERE WARRANTIES OF FITNESS FOR A PARTICULAR PURPOSE OR MERCHANTABILITY APPLICABLE TO THE PRODUCTS. THIS LIMITED WARRANTY DOES NOT COVER CUSTOM PRODUCTS. THIS LIMITED WARRANTY ALSO DOES NOT COVER IMPROPER OR POOR INSTALLATION OF THE PRODUCTS, WHICH INCLUDES BUT IS NOT LIMITED TO SQUEEGEEING, TRIMMING AND MEASURING. TO THE FULLEST EXTENT PERMITTED BY LAW, THIS LIMITED WARRANTY DOES NOT EXTEND TO, AND IN NO EVENT SHALL XPEL OR ANY AUTHORIZED XPEL INSTALLER BE LIABLE FOR, ANY INDIRECT, SPECIAL, INCIDENTAL, EXEMPLARY, CONSEQUENTIAL OR OTHER DAMAGE ARISING OUT OF THE INSTALLATION OR USE OF THE PRODUCT. SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THE EXPRESS WARRANTIES AND REMEDIES DESCRIBED ABOVE ARE THE EXCLUSIVE WARRANTIES AND REMEDIES AVAILABLE AND ARE IN LIEU OF ALL OTHER WARRANTIES AND REMEDIES, EXPRESS OR IMPLIED. XPEL HEREBY DISCLAIMS ALL OTHER EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TO THE FULLEST EXTENT PERMITTED BY LAW, IN NO EVENT SHALL XPEL’S LIABILITY EXCEED THE PRICE PAID FOR THE PRODUCT. THIS PROVISION SETS AN UPPER LIMIT TO THE AMOUNT OF DAMAGES, IF ANY, THAT THE OWNER OF THE PRODUCT MAY RECOVER FOR ANY AND ALL CLAIMS AND CAUSES OF ACTION. THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM JURISDICTION TO JURISDICTION.

TO MAKE A WARRANTY CLAIM

This Limited Warranty is the Product owner’s sole and exclusive remedy. To file a warranty claim, you must first submit, within the Limited Warranty period, this warranty card and a copy of your original receipt for the Product identifying coverage areas, along with a detailed description of the purported defect to the authorized XPEL installer who performed the installation of the Product, or in the event you are unable to contact the original authorized XPEL installer, to XPEL at the address below. All warranty claims must include the claimant’s name, phone number, address and the installation address (if different). All warranty claims must be approved by XPEL, and XPEL has the sole authority and discretion to determine the validity of all claims. XPEL reserves the right to deny claims that do not meet the criteria or are otherwise excluded as described above. For more information on this Limited Warranty, call the toll-free telephone number listed below.

XPEL, Inc.
711 Broadway St., Ste. 320
San Antonio, Texas 78215
(800) 447-9928
support@xpel.com

DISPUTE RESOLUTION

By installing or using the Product, you agree to use, and shall use, only the dispute resolution procedure provided herein to assert any and all claims, causes of action or demands arising from or related to the Product or this Limited Warranty. First, within the Limited Warranty period, you shall notify XPEL, in writing, of the specific act and/or omission that forms the basis of your claim related to the Product and/or your contention that XPEL has not performed its obligations under this Limited Warranty. XPEL shall have no less than thirty (30) days after receipt of your written notification to review your contention, during which time you are prohibited from taking any further legal action. You must use this procedure as a condition precedent to pursue any other legal action or remedy. The written notice required under this informal dispute resolution process must be made to:

XPEL, Inc.
711 Broadway St., Ste. 320
San Antonio, Texas 78215

Second, if your claim or contention is not resolved within thirty (30) days after XPEL’s receipt of your written notification above, any and all claims, causes of action or demands arising from or related to the Product or this Limited Warranty will be subject to mandatory, good-faith mediation to take place in San Antonio, Texas, United States of America at a mutually agreeable time, or at such other location to which XPEL, in its sole discretion, agrees in writing. Such mediation must be held within sixty (60) days after the date that you notify XPEL, in writing, of the specific act and/or omission that forms the basis of your claim related to the Product and/or your contention that XPEL has not performed its obligations under this Limited Warranty. Your good faith participation in such mediation is a condition precedent to the initiation or filing of any arbitration or legal proceeding against XPEL. Third, if such mediation is unsuccessful, any and all claims, causes of action or demands arising from or related to the Product or this Limited Warranty will be subject to binding arbitration administered by JAMS. By installing or using the Product, you agree that the exclusive and mandatory venue and location for any arbitration arising from or related to the Product or this Limited Warranty shall be in San Antonio, Texas, United States of America, unless XPEL agrees in writing, at its sole discretion, to conduct such arbitration in another venue or location. You may file suit against XPEL in a court of competent jurisdiction only to enforce an award rendered, if any, in an arbitration conducted pursuant to this Limited Warranty. With the sole exception of your right to enforce an arbitration award as provided herein, by installing or using the Product, you agree to: (1) waive any and all right to assert or maintain litigation against XPEL in any court, tribunal or any foreign or international forum, and (2) waive any and all right to a trial by jury.

SPECIAL RESTRICTIONS ON GLASS BREAKAGE AND SEAL FAILURE WARRANTY

Many applications of XPEL films are automatically covered for glass breakage in accordance with the above schedule. However, certain darker films and certain types of glass do not qualify for coverage unless written approval has been obtained in advance of installation from XPEL. Certain film and glass combinations require pre-approval, or are excluded. (See Film to Glass Chart for details)

NOTE: IF GLASS IS REPLACED BY THE CUSTOMER PRIOR TO MAKING A WARRANTY CLAIM FOR GLASS BREAKAGE OR SEAL FAILURE, THIS LIMITED WARRANTY IS VOIDED, UNLESS A DANGEROUS SITUATION EXISTS WHICH REQUIRES IMMEDIATE REPLACEMENT, IN WHICH CASE, THE CUSTOMER MUST TAKE A PHOTOGRAPH(S) THAT CLEARLY DEPICTS THE GLASS BREAKAGE OR SEAL FAILURE PRIOR TO REPLACING THE WINDOW. THE CUSTOMER MUST SUBMIT INFORMATION EVIDENCING THE DANGEROUS SITUATION AND THE REQUIRED PHOTOGRAPH(S) WITH ANY WARRANTY CLAIM.

VISION Home & Office · Coverage by film series

Series

Commercial

Residential

Glass breakage

Seal failure

SOLAR

Clear View, Daylight, Dark Neutral, Silver, Bronze, All Season

Commercial

15 years

Residential

Limited lifetime

Glass breakage

5 years

Seal failure

3 years

SOLAR · EVENING VIEW & BLEND DR

Evening View and Blend DR

Commercial

10 years

Residential

Limited lifetime

Glass breakage

5 years

Seal failure

3 years

SECURITY

4, 8 and 14 mil

Commercial

10 years

Residential

Limited lifetime

Glass breakage

5 years

Seal failure

3 years

SOLAR SECURITY

Clear View Plus 8 mil, Neutral 50 & 35, Silver 15

Commercial

10 years

Residential

Limited lifetime

Glass breakage

5 years

Seal failure

3 years

EXTERIOR

All exterior films

Commercial

5 / 2 years*

Residential

5 / 2 years*

Glass breakage

None

Seal failure

None

DECORATIVE

All decorative films

Commercial

5 years

Residential

5 years

Glass breakage

None

Seal failure

None

ANTI-GRAFFITI

All anti-graffiti films

Commercial

3 years

Residential

3 years

Glass breakage

None

Seal failure

None

BLISTER PREVENTION

Blister prevention film

Commercial

3 years

Residential

3 years

Glass breakage

None

Seal failure

None

* Exterior films come with a film replacement warranty for 5 years and a labor warranty for 2 years. Scaffolding and other equipment or related costs are excluded.

// 03 · XPEL FUSION PLUS

CERAMIC COATING.

Product · What’s covered

Coverage

Transfer

Annual check

Terms

01 //

PREMIUM v2

Oxidation, loss of gloss, UV damage and color fading.

8 YRS

from install date

Transfer:

YES

Annual check:

REQUIRED

XPEL PDF ↗

Limited Product Warranty

FUSION PLUS PREMIUM v2

XPEL, Inc. (the “Company”) expressly warrants to the owner that, for a period of eight (8) years from the date of initial installation (the “Warranty Period”), the Company will cover the vehicle’s paint finish and XPEL paint protection films finish on the FUSION PLUS PREMIUM v2 (the “Product(s)”) against: oxidation, loss of gloss, UV damage and color fading. This Limited Warranty only applies to the Company’s Products which are professionally installed in the manner recommended by the Company.

The Company will, at its option, remove or replace the Product without charge, or refund the cost of the Product, if the Product fails or does not perform as warranted solely due to a manufacturing defect within the Warranty Period, subject to the exclusions set forth in this Limited Warranty. If the Company elects to replace the Product, the Company will have an authorized installer of its choice remove and reapply the Product to areas determined by the Company in its sole discretion to be covered by this Limited Warranty. The Company will cover parts and the authorized installer will be responsible for providing installation labor. The refund of the cost of the Product or replacement of the defective coating are the exclusive remedies for all Products covered under this Limited Warranty. During the entire Warranty Period, the Company’s obligation as to repair or replacement shall further be limited to repair or replacement with the Products that are available at the time of the repair or replacement, shall be limited to the repair or replacement of only the specific Product that fails due to a manufacturing defect. The maximum replacement cost to be paid by the Company shall be the lesser of the cost of the coating application or $1000. Any repaired or replaced product shall also remain subject to the Warranty Period, and any repair or replacement shall not extend the original Warranty Period in any manner or start a new warranty period. These are the exclusive remedies for all Products covered under this Limited Warranty.

You may obtain coverage under this Limited Warranty by providing Company with proof of warranty card, copy of original receipt for the Product identifying coverage areas, along with a detailed description of the purported defect. For service under this Limited Warranty, you must notify the authorized Company installer who performed the installation of the Product, in writing, providing claimant’s name, phone number, address, and the installation address (if different), a description of the product involved and the nature of the defect.

This Limited Warranty is transferable only when the new owner submits to the Company proof of the original date of installation. Transfer of the Limited Warranty only entitles the new owner coverage for the remainder of the original Warranty Period.

Disclaimer Of Warranties

The Company’s Products must be stored, handled, installed, used, and maintained in accordance with instructions provided by the Company, and this Limited Warranty is conditioned upon compliance with all such instructions. Copies of the Company’s guides are available from the Company at the address listed below. You may also obtain this/these materials by contacting Company at +1 (210) 678-3700 or on the Company’s website at www.xpel.com/fusion-plus.

This Limited Warranty does not cover defects caused by:

1. Non-compliance with the Company’s guide or instructions. Such failures include, but are not limited to, exposure to physical abuse, including, but not limited to chemical abuse (e.g. harsh cleansers and solvents), thermal abuse or shock (e.g. excessive heat or cold) or misuse;
2. Improper storage, installation, handling and/or use of the Product;
3. Damage not resulting from manufacturing defects that occur while the Product is in the customer’s possession;
4. Unreasonable or unintended use of Product;
5. Products installed with known or visible manufacturing defects at the time of installation, including, but not limited to scratches, scuffs, scrapes, chips to the painted surface;
6. Minor conditions such as stains, and scratches;
7. Damage to the coated surface due to improper wash techniques, automatic car washes or incorrect wash tools that may cause abrasion or by third parties not authorized by the Company;
8. Scratches, scuffs, scrapes, chips to the painted surface;
9. Water spots – water spots are caused by mineral deposits, which if left to dry on the paint and/or PPF may leave a stain, water spots are not covered;
10. Damaged caused by collision, accidental damage, vandalism, fire, hail, flood, stones, collision, surface rust, rail dust, physical damage, paint overspray, or vehicle manufacturer’ defects, which may be covered under manufactures protection plan; and
11. Areas that have not been re-coated after a paint or body repair;
12. Use in non-automotive applications.

Any information or suggestion by the Company with respect to the Products concerning applications, specifications or compliance with codes and standards is provided solely for your convenient reference and are made without any representation as to accuracy or suitability. You must verify and test the suitability of any information with respect to the Products for your specific application.

THE WARRANTIES SET FORTH HEREIN ARE THE ONLY WARRANTIES MADE BY THE COMPANY IN CONNECTION WITH THESE PRODUCTS. THE COMPANY CAN NOT AND DOES NOT MAKE ANY IMPLIED OR EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, AND DISCLAIMS ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PRODUCTS SOLD BY COMPANY ARE SOLD ONLY TO THE SPECIFICATIONS SPECIFICALLY SET FORTH BY COMPANY IN WRITING. OTHER THAN THE LIMITED WARRANTY SET FORTH HEREIN, THE COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY’S SOLE OBLIGATION UNDER THIS WARRANTY SHALL BE REPAIR OR REPLACEMENT OF NON-CONFORMING PRODUCTS, OR AT THE OPTION OF THE COMPANY, RETURN OF THE PRODUCT AND A REFUND OF THE PURCHASE PRICE. BUYER ASSUMES ALL RISK WHATSOEVER AS TO THE RESULT OF THE USE OF THE PRODUCTS PURCHASED, WHETHER USED SINGULARLY OR IN COMBINATION WITH ANY OTHER PRODUCTS OR SUBSTANCES.

Limitation Of Liability

Annual Inspections

To maintain the warranty on your product, an annual inspection is required throughout the warranty period, as stated in the product specifications. This inspection should be performed by an XPEL certified Fusion Installer every year and must be completed within 30 days before or after the anniversary date of installation or the date of any previous inspection or service. Failure to complete the inspection, within the required time will void the Limited Warranty. Any fees or charges by the XPEL Certified Installer will be charged to the owner to do the annual inspection including, but not limited to, exterior wash, decontamination, inspection, and a single layer application of XPEL FUSION PLUS LITE Ceramic Coating. Please keep proof of all inspections, as they must be provided if you have a Limited Warranty related issue.

Contact Information

02 //

CLASSIC

Oxidation, loss of gloss, UV damage, color fading.

4 YRS

from install date

Transfer:

YES

Annual check:

REQUIRED

XPEL PDF ↗

Limited Product Warranty

FUSION PLUS CLASSIC

XPEL, Inc. (the “Company”) expressly warrants to the owner that, for a period of four (4) years from the date of initial installation (the “Warranty Period”), the Company will cover the vehicles paint finish and XPEL paint protection films finish on the FUSION PLUS CLASSIC (the “Product(s)”) against: oxidation, loss of gloss, UV damage, color fading. This Limited Warranty only applies to the Company’s Products which are professionally installed in the manner recommended by the Company.

The Company will, at its option, remove or replace the Product without charge, or refund the cost of the Product, if the Product fails or does not perform as warranted solely due to a manufacturing defect within the Warranty Period, subject to the exclusions set forth in this Limited Warranty. If the Company elects to replace the Product, the Company will have an authorized installer of its choice remove and reapply the Product to areas determined by the Company in its sole discretion to be covered by this Limited Warranty. The Company will cover parts and the authorized installer will be responsible for providing installation labor. The refund of the cost of the Product or replacement of the defective coating are the exclusive remedies for all Products covered under this Limited Warranty. During the entire Warranty Period, the Company’s obligation as to repair or replacement shall further be limited to repair or replacement with the Products that are available at the time of the repair or replacement, shall be limited to the repair or replacement of only the specific Product that fails due to a manufacturing defect. The maximum replacement cost to be paid by the Company shall be the lesser of the cost of the coating application or $1000. Any repaired or replaced product shall also remain subject to the Warranty Period, and any repair or replacement shall not extend the original Warranty Period in any manner or start a new warranty period. These are the exclusive remedies for all Products covered under this Limited Warranty.

You may obtain coverage under this Limited Warranty by providing Company with proof of warranty card, copy of original receipt for the Product identifying coverage areas, along with a detailed description of the purported defect. For service under this Limited Warranty, you must notify the authorized Company installer who performed the installation of the Product, in writing, providing claimant’s name, phone number, address, and the installation address (if different), a description of the product involved and the nature of the defect.

This Limited Warranty is transferable only when the new owner submits to the Company proof of the original date of installation. Transfer of the Limited Warranty only entitles the new owner coverage for the remainder of the original Warranty Period.

Disclaimer Of Warranties

The Company’s Products must be stored, handled, installed, used, and maintained in accordance with instructions provided by the Company, and this Limited Warranty is conditioned upon compliance with all such instructions. Copies of the Company’s guides are available from the Company at the address listed below. You may also obtain this/these materials by contacting Company at +1 (210) 678-3700 or on the Company’s website at www.xpel.com/fusion-plus.

This Limited Warranty does not cover defects caused by:

1. Non-compliance with the Company’s guide or instructions. Such failures include, but are not limited to, exposure to physical abuse, including, but not limited to chemical abuse (e.g. harsh cleansers and solvents), thermal abuse or shock (e.g. excessive heat or cold) or misuse;
2. Improper storage, installation, handling and/or use of the Product;
3. Damage not resulting from manufacturing defects that occur while the Product is in the customer’s possession;
4. Unreasonable or unintended use of Product;
5. Products installed with known or visible manufacturing defects at the time of installation, including, but not limited to scratches, scuffs, scrapes, chips to the painted surface;
6. Minor conditions such as stains, and scratches;
7. Damage to the coated surface due to improper wash techniques, automatic car washes or incorrect wash tools that may cause abrasion or by third parties not authorized by the Company;
8. Scratches, scuffs, scrapes, chips to the painted surface;
9. Water spots – water spots are caused by mineral deposits, which if left to dry on the paint and/or PPF may leave a stain, water spots are not covered;
10. Damaged caused by collision, accidental damage, vandalism, fire, hail, flood, stones, collision, surface rust, rail dust, physical damage, paint overspray, or vehicle manufacturer’ defects, which may be covered under manufactures protection plan;
11. Areas that have not been re-coated after a paint or body repair;
12. Use in non-automotive applications.

Any information or suggestion by the Company with respect to the Products concerning applications, specifications or compliance with codes and standards is provided solely for your convenient reference and are made without any representation as to accuracy or suitability. You must verify and test the suitability of any information with respect to the Products for your specific application.

THE WARRANTIES SET FORTH HEREIN ARE THE ONLY WARRANTIES MADE BY THE COMPANY IN CONNECTION WITH THESE PRODUCTS. THE COMPANY CAN NOT AND DOES NOT MAKE ANY IMPLIED OR EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, AND DISCLAIMS ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PRODUCTS SOLD BY COMPANY ARE SOLD ONLY TO THE SPECIFICATIONS SPECIFICALLY SET FORTH BY COMPANY IN WRITING. OTHER THAN THE LIMITED WARRANTY SET FORTH HEREIN, THE COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY’S SOLE OBLIGATION UNDER THIS WARRANTY SHALL BE REPAIR OR REPLACEMENT OF NON-CONFORMING PRODUCTS, OR AT THE OPTION OF THE COMPANY, RETURN OF THE PRODUCT AND A REFUND OF THE PURCHASE PRICE. BUYER ASSUMES ALL RISK WHATSOEVER AS TO THE RESULT OF THE USE OF THE PRODUCTS PURCHASED, WHETHER USED SINGULARLY OR IN COMBINATION WITH ANY OTHER PRODUCTS OR SUBSTANCES.

Limitation Of Liability

Annual Inspections

Contact Information

03 //

PAINT & PPF

Oxidation, loss of gloss, UV damage, color fading.

4 YRS

from install date

Transfer:

YES

Annual check:

REQUIRED

XPEL PDF ↗

Limited Product Warranty

FUSION PLUS PAINT & PPF

XPEL, Inc. (the “Company”) expressly warrants to the owner that, for a period of four (4) years from the date of initial installation (the “Warranty Period”), the Company will cover the vehicles paint finish and XPEL paint protection films finish on the FUSION PLUS PAINT & PPF (the “Product(s)”) against: oxidation, loss of gloss, UV damage, color fading. This Limited Warranty only applies to the Company’s Products which are professionally installed in the manner recommended by the Company.

The Company will, at its option, remove or replace the Product without charge, or refund the cost of the Product, if the Product fails or does not perform as warranted solely due to a manufacturing defect within the Warranty Period, subject to the exclusions set forth in this Limited Warranty. If the Company elects to replace the Product, the Company will have an authorized installer of its choice remove and reapply the Product to areas determined by the Company in its sole discretion to be covered by this Limited Warranty. The Company will cover parts and the authorized installer will be responsible for providing installation labor. The refund of the cost of the Product or replacement of the defective coating are the exclusive remedies for all Products covered under this Limited Warranty. During the entire Warranty Period, the Company’s obligation as to repair or replacement shall further be limited to repair or replacement with the Products that are available at the time of the repair or replacement, shall be limited to the repair or replacement of only the specific Product that fails due to a manufacturing defect. The maximum replacement cost to be paid by the Company shall be the lesser of the cost of the coating application or $1000. Any repaired or replaced product shall also remain subject to the Warranty Period, and any repair or replacement shall not extend the original Warranty Period in any manner or start a new warranty period. These are the exclusive remedies for all Products covered under this Limited Warranty.

You may obtain coverage under this Limited Warranty by providing Company with proof of warranty card, copy of original receipt for the Product identifying coverage areas, along with a detailed description of the purported defect. For service under this Limited Warranty, you must notify the authorized Company installer who performed the installation of the Product, in writing, providing claimant’s name, phone number, address, and the installation address (if different), a description of the product involved and the nature of the defect.

This Limited Warranty is transferable only when the new owner submits to the Company proof of the original date of installation. Transfer of the Limited Warranty only entitles the new owner coverage for the remainder of the original Warranty Period.

Disclaimer Of Warranties

The Company’s Products must be stored, handled, installed, used, and maintained in accordance with instructions provided by the Company, and this Limited Warranty is conditioned upon compliance with all such instructions. Copies of the Company’s guides are available from the Company at the address listed below. You may also obtain this/these materials by contacting Company at +1 (210) 678-3700 or on the Company’s website at www.xpel.com/fusion-plus.

This Limited Warranty does not cover defects caused by:

1. Non-compliance with the Company’s guide or instructions. Such failures include, but are not limited to, exposure to physical abuse, including, but not limited to chemical abuse (e.g. harsh cleansers and solvents), thermal abuse or shock (e.g. excessive heat or cold) or misuse;
2. Improper storage, installation, handling and/or use of the Product;
3. Damage not resulting from manufacturing defects that occur while the Product is in the customer’s possession;
4. Unreasonable or unintended use of Product;
5. Products installed with known or visible manufacturing defects at the time of installation, including, but not limited to scratches, scuffs, scrapes, chips to the painted surface;
6. Minor conditions such as stains, and scratches;
7. Damage to the coated surface due to improper wash techniques, automatic car washes or incorrect wash tools that may cause abrasion or by third parties not authorized by the Company;
8. Scratches, scuffs, scrapes, chips to the painted surface;
9. Water spots – water spots are caused by mineral deposits, which if left to dry on the paint and/or PPF may leave a stain, water spots are not covered;
10. Damaged caused by collision, accidental damage, vandalism, fire, hail, flood, stones, collision, surface rust, rail dust, physical damage, paint overspray, or vehicle manufacturer’ defects, which may be covered under manufactures protection plan;
11. Areas that have not been re-coated after a paint or body repair;
12. Use in non-automotive applications.

Any information or suggestion by the Company with respect to the Products concerning applications, specifications or compliance with codes and standards is provided solely for your convenient reference and are made without any representation as to accuracy or suitability. You must verify and test the suitability of any information with respect to the Products for your specific application.

THE WARRANTIES SET FORTH HEREIN ARE THE ONLY WARRANTIES MADE BY THE COMPANY IN CONNECTION WITH THESE PRODUCTS. THE COMPANY CAN NOT AND DOES NOT MAKE ANY IMPLIED OR EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, AND DISCLAIMS ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PRODUCTS SOLD BY COMPANY ARE SOLD ONLY TO THE SPECIFICATIONS SPECIFICALLY SET FORTH BY COMPANY IN WRITING. OTHER THAN THE LIMITED WARRANTY SET FORTH HEREIN, THE COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY’S SOLE OBLIGATION UNDER THIS WARRANTY SHALL BE REPAIR OR REPLACEMENT OF NON-CONFORMING PRODUCTS, OR AT THE OPTION OF THE COMPANY, RETURN OF THE PRODUCT AND A REFUND OF THE PURCHASE PRICE. BUYER ASSUMES ALL RISK WHATSOEVER AS TO THE RESULT OF THE USE OF THE PRODUCTS PURCHASED, WHETHER USED SINGULARLY OR IN COMBINATION WITH ANY OTHER PRODUCTS OR SUBSTANCES.

Limitation Of Liability

Annual Inspections

Contact Information

04 //

SATIN

Oxidation, loss of gloss, UV damage, color fading.

4 YRS

from install date

Transfer:

YES

Annual check:

REQUIRED

XPEL PDF ↗

Limited Product Warranty

FUSION PLUS SATIN

XPEL, Inc. (the “Company”) expressly warrants to the owner that, for a period of four (4) years (the “Warranty Period”) from the date of initial installation. The Company will cover the vehicles paint finish on the FUSION PLUS SATIN (the “Product(s)”) against: oxidation, loss of gloss, UV damage, color fading. This Limited Warranty only applies to the Company’s Products which are professionally installed in the manner recommended by the Company.

The Company will, at its option, remove or replace the Product without charge, or refund the cost of the Product, if the Product fails or does not perform as warranted solely due to a manufacturing defect within the Warranty Period, subject to the exclusions set forth in this Limited Warranty. If the Company elects to replace the Product, the Company will have an authorized installer of its choice remove and reapply the Product to areas determined by the Company in its sole discretion to be covered by this Limited Warranty. The Company will cover parts and the authorized installer will be responsible for providing installation labor. The refund of the cost of the Product or replacement of the defective coating are the exclusive remedies for all Products covered under this Limited Warranty. During the entire Warranty Period, the Company’s obligation as to repair or replacement shall further be limited to repair or replacement with the Products that are available at the time of the repair or replacement, shall be limited to the repair or replacement of only the specific Product that fails due to a manufacturing defect. The maximum replacement cost to be paid by the Company shall be the lesser of the cost of the coating application or $1000. Any repaired or replaced product shall also remain subject to the Warranty Period, and any repair or replacement shall not extend the original Warranty Period in any manner or start a new warranty period. These are the exclusive remedies for all Products covered under this Limited Warranty.

You may obtain coverage under this Limited Warranty by providing Company with proof of warranty card, copy of original receipt for the Product identifying coverage areas, along with a detailed description of the purported defect. For service under this Limited Warranty, you must notify the authorized Company installer who performed the installation of the Product, in writing, providing claimant’s name, phone number, address, and the installation address (if different), a description of the product involved and the nature of the defect.

This Limited Warranty is transferable only when the new owner submits to the Company proof of the original date of installation. Transfer of the Limited Warranty only entitles the new owner coverage for the remainder of the original Warranty Period.

Disclaimer Of Warranties

The Company’s Products must be stored, handled, installed, used, and maintained in accordance with instructions provided by the Company, and this Limited Warranty is conditioned upon compliance with all such instructions. Copies of the Company’s guides are available from the Company at the address listed below. You may also obtain this/these materials by contacting Company at +1-210-678-3700 or on the Company’s website at www.xpel.com/fusion-plus.

This Limited Warranty does not cover defects caused by:

1. Non-compliance with the Company’s guide or instructions. Such failures include, but are not limited to, exposure to physical abuse, including, but not limited to chemical abuse (e.g. harsh cleansers and solvents), thermal abuse or shock (e.g. excessive heat or cold) or misuse;
2. Improper storage, installation, handling and/or use of the Product;
3. Damage not resulting from manufacturing defects that occur while the Product is in the customer’s possession;
4. Unreasonable or unintended use of Product;
5. Products installed with known or visible manufacturing defects at the time of installation, including, but not limited to scratches, scuffs, scrapes, chips to the painted surface;
6. Minor conditions such as stains, and scratches;
7. Damage to the coated surface due to improper wash techniques, automatic car washes or incorrect wash tools that may cause abrasion or by third parties not authorized by the Company;
8. Scratches, scuffs, scrapes, chips to the painted surface;
9. Water spots – water spots are caused by mineral deposits, which if left to dry on the paint and/or PPF may leave a stain;
10. Damaged caused by collision, accidental damage, vandalism, fire, hail, flood, stones, collision, surface rust, rail dust, physical damage, paint overspray, or vehicle manufacturer’ defects, which may be covered under manufactures protection plan; and
11. Areas that have not been re-coated after a paint or body repair;
12. Use in non-automotive applications.

Any information or suggestion by the Company with respect to the Products concerning applications, specifications or compliance with codes and standards is provided solely for your convenient reference and are made without any representation as to accuracy or suitability. You must verify and test the suitability of any information with respect to the Products for your specific application.

THE WARRANTIES SET FORTH HEREIN ARE THE ONLY WARRANTIES MADE BY THE COMPANY IN CONNECTION WITH THESE PRODUCTS. THE COMPANY CAN NOT AND DOES NOT MAKE ANY IMPLIED OR EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, AND DISCLAIMS ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PRODUCTS SOLD BY COMPANY ARE SOLD ONLY TO THE SPECIFICATIONS SPECIFICALLY SET FORTH BY COMPANY IN WRITING. OTHER THAN THE LIMITED WARRANTY SET FORTH HEREIN, THE COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY’S SOLE OBLIGATION UNDER THIS WARRANTY SHALL BE REPAIR OR REPLACEMENT OF NON-CONFORMING PRODUCTS, OR AT THE OPTION OF THE COMPANY, RETURN OF THE PRODUCT AND A REFUND OF THE PURCHASE PRICE. BUYER ASSUMES ALL RISK WHATSOEVER AS TO THE RESULT OF THE USE OF THE PRODUCTS PURCHASED, WHETHER USED SINGULARLY OR IN COMBINATION WITH ANY OTHER PRODUCTS OR SUBSTANCES.

Limitation Of Liability

Annual Inspections

Annual inspections must be carried out by an XPEL Certified Installer, within thirty (30) days before or after the installation date of the application or last service date. Failure to complete the inspection, within the required time will void the Limited Warranty. Any fees or charges by the XPEL Certified Installer will be charged to the owner to do the annual inspection including, but not limited to, exterior wash, decontamination, and inspection. Please keep proof of all inspections, as they must be provided if you have a Limited Warranty related issue.

Contact Information

05 //

LITE

Oxidation, loss of gloss, UV damage and color fading.

1 YR

from install date

Transfer:

YES

Annual check:

NOT NEEDED

XPEL PDF ↗

Limited Product Warranty

FUSION PLUS LITE

XPEL, Inc. (the “Company”) expressly warrants to the owner that, for a period of one (1) year from the date of initial installation (the “Warranty Period”), the Company will cover the vehicle’s paint finish and XPEL paint protection films finish on the FUSION PLUS LITE (the “Product(s)”) against: oxidation, loss of gloss, UV damage and color fading. This Limited Warranty only applies to the Company’s Products which are professionally installed in the manner recommended by the Company.

The Company will, at its option, remove or replace the Product without charge, or refund the cost of the Product, if the Product fails or does not perform as warranted solely due to a manufacturing defect within the Warranty Period, subject to the exclusions set forth in this Limited Warranty. If the Company elects to replace the Product, the Company will have an authorized installer of its choice remove and reapply the Product to areas determined by the Company in its sole discretion to be covered by this Limited Warranty. The Company will cover parts and the authorized installer will be responsible for providing installation labor. The refund of the cost of the Product or replacement of the defective coating are the exclusive remedies for all Products covered under this Limited Warranty. During the entire Warranty Period, the Company’s obligation as to repair or replacement shall further be limited to repair or replacement with the Products that are available at the time of the repair or replacement, shall be limited to the repair or replacement of only the specific Product that fails due to a manufacturing defect. The maximum replacement cost to be paid by the Company shall be the lesser of the cost of the coating application or $1000. Any repaired or replaced product shall also remain subject to the Warranty Period, and any repair or replacement shall not extend the original Warranty Period in any manner or start a new warranty period. These are the exclusive remedies for all Products covered under this Limited Warranty.

You may obtain coverage under this Limited Warranty by providing Company with proof of warranty card, copy of original receipt for the Product identifying coverage areas, along with a detailed description of the purported defect. For service under this Limited Warranty, you must notify the authorized Company installer who performed the installation of the Product, in writing, providing claimant’s name, phone number, address, and the installation address (if different), a description of the product involved and the nature of the defect.

This Limited Warranty is transferable only when the new owner submits to the Company proof of the original date of installation. Transfer of the Limited Warranty only entitles the new owner coverage for the remainder of the original Warranty Period.

Disclaimer Of Warranties

The Company’s Products must be stored, handled, installed, used, and maintained in accordance with instructions provided by the Company, and this Limited Warranty is conditioned upon compliance with all such instructions. Copies of the Company’s guides are available from the Company at the address listed below. You may also obtain this/these materials by contacting Company at +1 (210) 678-3700 or on the Company’s website at www.xpel.com/fusion-plus.

This Limited Warranty does not cover defects caused by:

1. Non-compliance with the Company’s guide or instructions. Such failures include, but are not limited to, exposure to physical abuse, including, but not limited to chemical abuse (e.g. harsh cleansers and solvents), thermal abuse or shock (e.g. excessive heat or cold) or misuse;
2. Improper storage, installation, handling and/or use of the Product;
3. Damage not resulting from manufacturing defects that occur while the Product is in the customer’s possession;
4. Unreasonable or unintended use of Product;
5. Products installed with known or visible manufacturing defects at the time of installation, including, but not limited to scratches, scuffs, scrapes, chips to the painted surface;
6. Minor conditions such as stains, and scratches;
7. Damage to the coated surface due to improper wash techniques, automatic car washes or incorrect wash tools that may cause abrasion or by third parties not authorized by the Company;
8. Scratches, scuffs, scrapes, chips to the painted surface;
9. Water spots – water spots are caused by mineral deposits, which if left to dry on the paint and/or PPF may leave a stain, water spots are not covered;
10. Damaged caused by collision, accidental damage, vandalism, fire, hail, flood, stones, collision, surface rust, rail dust, physical damage, paint overspray, or vehicle manufacturer’ defects, which may be covered under manufactures protection plan;
11. Areas that have not been re-coated after a paint or body repair;
12. Use in non-automotive applications.

Any information or suggestion by the Company with respect to the Products concerning applications, specifications or compliance with codes and standards is provided solely for your convenient reference and are made without any representation as to accuracy or suitability. You must verify and test the suitability of any information with respect to the Products for your specific application.

THE WARRANTIES SET FORTH HEREIN ARE THE ONLY WARRANTIES MADE BY THE COMPANY IN CONNECTION WITH THESE PRODUCTS. THE COMPANY CAN NOT AND DOES NOT MAKE ANY IMPLIED OR EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, AND DISCLAIMS ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PRODUCTS SOLD BY COMPANY ARE SOLD ONLY TO THE SPECIFICATIONS SPECIFICALLY SET FORTH BY COMPANY IN WRITING. OTHER THAN THE LIMITED WARRANTY SET FORTH HEREIN, THE COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY’S SOLE OBLIGATION UNDER THIS WARRANTY SHALL BE REPAIR OR REPLACEMENT OF NON-CONFORMING PRODUCTS, OR AT THE OPTION OF THE COMPANY, RETURN OF THE PRODUCT AND A REFUND OF THE PURCHASE PRICE. BUYER ASSUMES ALL RISK WHATSOEVER AS TO THE RESULT OF THE USE OF THE PRODUCTS PURCHASED, WHETHER USED SINGULARLY OR IN COMBINATION WITH ANY OTHER PRODUCTS OR SUBSTANCES.

Limitation Of Liability

Contact Information

06 //

WHEEL & CALIPER

Loss of gloss and environmental contaminant staining.

3 YRS

from install date

Transfer:

YES

Annual check:

REQUIRED

XPEL PDF ↗

Limited Product Warranty

FUSION PLUS WHEEL & CALIPER

XPEL, Inc. (the “Company”) expressly warrants to the owner that, for a period of three (3) years (the “Warranty Period”) from the date of initial installation. The Company will cover the vehicles wheel and calipers on the FUSION PLUS WHEEL & CALIPER (the “Product(s)”) against: loss of gloss and environmental contaminant staining. This Limited Warranty only applies to the Company’s Products which are professionally installed in the manner recommended by the Company.

The Company will, at its option, remove or replace the Product without charge, or refund the cost of the Product, if the Product fails or does not perform as warranted solely due to a manufacturing defect within the Warranty Period, subject to the exclusions set forth in this Limited Warranty. If the Company elects to replace the Product, the Company will have an authorized installer of its choice remove and reapply the Product to areas determined by the Company in its sole discretion to be covered by this Limited Warranty. The Company will cover parts and the authorized installer will be responsible for providing installation labor. The refund of the cost of the Product or replacement of the defective coating are the exclusive remedies for all Products covered under this Limited Warranty. During the entire Warranty Period, the Company’s obligation as to repair or replacement shall further be limited to repair or replacement with the Products that are available at the time of the repair or replacement, shall be limited to the repair or replacement of only the specific Product that fails due to a manufacturing defect. The maximum replacement cost to be paid by the Company shall be the lesser of the cost of the coating application or $500. Any repaired or replaced product shall also remain subject to the Warranty Period, and any repair or replacement shall not extend the original Warranty Period in any manner or start a new warranty period. These are the exclusive remedies for all Products covered under this Limited Warranty.

You may obtain coverage under this Limited Warranty by providing Company with proof of warranty card, copy of original receipt for the Product identifying coverage areas, along with a detailed description of the purported defect. For service under this Limited Warranty, you must notify the authorized Company installer who performed the installation of the Product, in writing, providing claimant’s name, phone number, address, and the installation address (if different), a description of the product involved and the nature of the defect.

This Limited Warranty is transferable only when the new owner submits to the Company proof of the original date of installation. Transfer of the Limited Warranty only entitles the new owner coverage for the remainder of the original Warranty Period.

Disclaimer Of Warranties

The Company’s Products must be stored, handled, installed, used, and maintained in accordance with instructions provided by the Company, and this Limited Warranty is conditioned upon compliance with all such instructions. Copies of the Company’s guides are available from the Company at the address listed below. You may also obtain this/these materials by contacting Company at +1-210-678-3700 or on the Company’s website at www.xpel.com/fusion-plus.

This Limited Warranty does not cover defects caused by:

1. Non-compliance with the Company’s guide or instructions. Such failures include, but are not limited to, exposure to physical abuse, including, but not limited to chemical abuse (e.g. harsh cleansers and solvents), thermal abuse or shock (e.g. excessive heat or cold) or misuse;
2. Improper storage, installation, handling and/or use of the Product;
3. Damage not resulting from manufacturing defects that occur while the Product is in the customer’s possession;
4. Unreasonable or unintended use of Product;
5. Products installed with known or visible manufacturing defects at the time of installation, including, but not limited to failing clear coat, swirl marks, scratches, scuffs, scrapes, chips to the wheel and caliper surface;
6. Minor conditions such as stains, and scratches;
7. Damage to the coated surface due to improper wash techniques, automatic car washes or incorrect wash tools that may cause abrasion or by third parties not authorized by the Company;
8. Swirl marks, scratches, scuffs, scrapes, chips to the wheel and caliper surface;
9. Water spots – water spots are caused by mineral deposits, which if left to dry on the wheel and/or caliper and/or ceramic coating may leave a stain, water spots are not covered.
10. Damage caused by collision, accidental damage, vandalism, fire, hail, flood, stones, collision, surface rust, rail dust, physical damage, paint overspray, brake dust, or wheel and/or caliper manufacturer’ defects, which may be covered under manufactures protection plan; and
11. Areas that have not been re-coated after a paint or body repair;
12. Use in non-automotive applications.

Any information or suggestion by the Company with respect to the Products concerning applications, specifications or compliance with codes and standards is provided solely for your convenient reference and are made without any representation as to accuracy or suitability. You must verify and test the suitability of any information with respect to the Products for your specific application.

THE WARRANTIES SET FORTH HEREIN ARE THE ONLY WARRANTIES MADE BY THE COMPANY IN CONNECTION WITH THESE PRODUCTS. THE COMPANY CAN NOT AND DOES NOT MAKE ANY IMPLIED OR EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, AND DISCLAIMS ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PRODUCTS SOLD BY COMPANY ARE SOLD ONLY TO THE SPECIFICATIONS SPECIFICALLY SET FORTH BY COMPANY IN WRITING. OTHER THAN THE LIMITED WARRANTY SET FORTH HEREIN, THE COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY’S SOLE OBLIGATION UNDER THIS WARRANTY SHALL BE REPAIR OR REPLACEMENT OF NON-CONFORMING PRODUCTS, OR AT THE OPTION OF THE COMPANY, RETURN OF THE PRODUCT AND A REFUND OF THE PURCHASE PRICE. BUYER ASSUMES ALL RISK WHATSOEVER AS TO THE RESULT OF THE USE OF THE PRODUCTS PURCHASED, WHETHER USED SINGULARLY OR IN COMBINATION WITH ANY OTHER PRODUCTS OR SUBSTANCES.

Limitation Of Liability

Annual Inspections

Contact Information

07 //

GLASS

Loss of hydrophobicity and environmental contaminant staining.

2 YRS

from install date

Transfer:

YES

Annual check:

REQUIRED

XPEL PDF ↗

Limited Product Warranty

FUSION PLUS GLASS

XPEL, Inc. (the “Company”) expressly warrants to the owner that, for a period of two (2) years from the date of initial installation (the “Warranty Period”), the Company will cover the vehicles glass on the FUSION PLUS GLASS (the “Product(s)”) against: loss of hydrophobicity and environmental contaminant staining. This Limited Warranty only applies to the Company’s Products which are professionally installed in the manner recommended by the Company.

The Company will, at its option, remove or replace the Product without charge, or refund the cost of the Product, if the Product fails or does not perform as warranted solely due to a manufacturing defect within the Warranty Period, subject to the exclusions set forth in this Limited Warranty. If the Company elects to replace the Product, the Company will have an authorized installer of its choice remove and reapply the Product to areas determined by the Company in its sole discretion to be covered by this Limited Warranty. The Company will cover parts and the authorized installer will be responsible for providing installation labor. The refund of the cost of the Product or replacement of the defective coating are the exclusive remedies for all Products covered under this Limited Warranty. During the entire Warranty Period, the Company’s obligation as to repair or replacement shall further be limited to repair or replacement with the Products that are available at the time of the repair or replacement, shall be limited to the repair or replacement of only the specific Product that fails due to a manufacturing defect. The maximum replacement cost to be paid by the Company shall be the lesser of the cost of the coating application or $500. Any repaired or replaced product shall also remain subject to the Warranty Period, and any repair or replacement shall not extend the original Warranty Period in any manner or start a new warranty period. These are the exclusive remedies for all Products covered under this Limited Warranty.

You may obtain coverage under this Limited Warranty by providing Company with proof of warranty card, copy of original receipt for the Product identifying coverage areas, along with a detailed description of the purported defect. For service under this Limited Warranty, you must notify the authorized Company installer who performed the installation of the Product, in writing, providing claimant’s name, phone number, address, and the installation address (if different), a description of the product involved and the nature of the defect.

This Limited Warranty is transferable only when the new owner submits to the Company proof of the original date of installation. Transfer of the Limited Warranty only entitles the new owner coverage for the remainder of the original Warranty Period.

Disclaimer Of Warranties

The Company’s Products must be stored, handled, installed, used, and maintained in accordance with instructions provided by the Company, and this Limited Warranty is conditioned upon compliance with all such instructions. Copies of the Company’s guides are available from the Company at the address listed below. You may also obtain this/these materials by contacting Company at +1 (210) 678-3700 or on the Company’s website at www.xpel.com/fusion-plus.

This Limited Warranty does not cover defects caused by:

1. Non-compliance with the Company’s guide or instructions. Such failures include, but are not limited to, exposure to physical abuse, including, but not limited to chemical abuse (e.g. harsh cleansers and solvents), thermal abuse or shock (e.g. excessive heat or cold) or misuse;
2. Improper storage, installation, handling and/or use of the Product;
3. Damage not resulting from manufacturing defects that occur while the Product is in the customer’s possession;
4. Unreasonable or unintended use of Product;
5. Products installed with known or visible manufacturing defects at the time of installation, including, but not limited to scratches, scuffs, scrapes, chips to the glass surface;
6. Minor conditions such as stains, and scratches;
7. Damage to the coated surface due to improper wash techniques, automatic car washes or incorrect wash tools that may cause abrasion or by third parties not authorized by the Company;
8. Scratches, scuffs, scrapes, chips to the glass surface;
9. Water spots – water spots are caused by mineral deposits, which if left to dry on the glass surface and/or ceramic coating may leave a stain, water spots are not covered;
10. Damage caused by collision, accidental damage, vandalism, fire, hail, flood, surface rust, rail dust, physical damage, paint overspray, or glass manufacturer’ defects, which may be covered under manufactures protection plan; and
11. Areas that have not been re-coated after glass repair or replacement.
12. Use in non-automotive applications.

Any information or suggestion by the Company with respect to the Products concerning applications, specifications or compliance with codes and standards is provided solely for your convenient reference and are made without any representation as to accuracy or suitability. You must verify and test the suitability of any information with respect to the Products for your specific application.

THE WARRANTIES SET FORTH HEREIN ARE THE ONLY WARRANTIES MADE BY THE COMPANY IN CONNECTION WITH THESE PRODUCTS. THE COMPANY CAN NOT AND DOES NOT MAKE ANY IMPLIED OR EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, AND DISCLAIMS ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PRODUCTS SOLD BY COMPANY ARE SOLD ONLY TO THE SPECIFICATIONS SPECIFICALLY SET FORTH BY COMPANY IN WRITING. OTHER THAN THE LIMITED WARRANTY SET FORTH HEREIN, THE COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY’S SOLE OBLIGATION UNDER THIS WARRANTY SHALL BE REPAIR OR REPLACEMENT OF NON-CONFORMING PRODUCTS, OR AT THE OPTION OF THE COMPANY, RETURN OF THE PRODUCT AND A REFUND OF THE PURCHASE PRICE. BUYER ASSUMES ALL RISK WHATSOEVER AS TO THE RESULT OF THE USE OF THE PRODUCTS PURCHASED, WHETHER USED SINGULARLY OR IN COMBINATION WITH ANY OTHER PRODUCTS OR SUBSTANCES.

Limitation Of Liability

Annual Inspections

Terms Defined

Loss of hydrophobicity is determined by dewetting ability of a flat surface; significant loss would need to be provided in example during warranty claim process.

Contact Information

08 //

PLASTIC & TRIM

Environmental contaminant staining and fading.

1 YR

from install date

Transfer:

YES

Annual check:

REQUIRED

XPEL PDF ↗

Limited Product Warranty

FUSION PLUS PLASTIC & TRIM

XPEL, Inc. (the “Company”) expressly warrants to the owner that, for a period of one (1) year from the date of initial installation (the “Warranty Period”), the Company will cover the vehicles plastic and trim on the FUSION PLUS PLASTIC & TRIM (the “Product(s)”) against: environmental contaminant staining and fading. This Limited Warranty only applies to the Company’s Products which are professionally installed in the manner recommended by the Company.

The Company will, at its option, remove or replace the Product without charge, or refund the cost of the Product, if the Product fails or does not perform as warranted solely due to a manufacturing defect within the Warranty Period, subject to the exclusions set forth in this Limited Warranty. If the Company elects to replace the Product, the Company will have an authorized installer of its choice remove and reapply the Product to areas determined by the Company in its sole discretion to be covered by this Limited Warranty. The Company will cover parts and the authorized installer will be responsible for providing installation labor. The refund of the cost of the Product or replacement of the defective coating are the exclusive remedies for all Products covered under this Limited Warranty. During the entire Warranty Period, the Company’s obligation as to repair or replacement shall further be limited to repair or replacement with the Products that are available at the time of the repair or replacement, shall be limited to the repair or replacement of only the specific Product that fails due to a manufacturing defect. The maximum replacement cost to be paid by the Company shall be the lesser of the cost of the coating application or $250. Any repaired or replaced product shall also remain subject to the Warranty Period, and any repair or replacement shall not extend the original Warranty Period in any manner or start a new warranty period. These are the exclusive remedies for all Products covered under this Limited Warranty.

You may obtain coverage under this Limited Warranty by providing Company with proof of warranty card, copy of original receipt for the Product identifying coverage areas, along with a detailed description of the purported defect. For service under this Limited Warranty, you must notify the authorized Company installer who performed the installation of the Product, in writing, providing claimant’s name, phone number, address, and the installation address (if different), a description of the product involved and the nature of the defect.

This Limited Warranty is transferable only when the new owner submits to the Company proof of the original date of installation. Transfer of the Limited Warranty only entitles the new owner coverage for the remainder of the original Warranty Period.

Disclaimer Of Warranties

The Company’s Products must be stored, handled, installed, used, and maintained in accordance with instructions provided by the Company, and this Limited Warranty is conditioned upon compliance with all such instructions. Copies of the Company’s guides are available from the Company at the address listed below. You may also obtain this/these materials by contacting Company at +1 (210) 678-3700 or on the Company’s website at www.xpel.com/fusion-plus.

This Limited Warranty does not cover defects caused by:

1. Non-compliance with the Company’s guide or instructions. Such failures include, but are not limited to, exposure to physical abuse, including, but not limited to chemical abuse (e.g. harsh cleansers and solvents), thermal abuse or shock (e.g. excessive heat or cold) or misuse;
2. Improper storage, installation, handling and/or use of the Product;
3. damage not resulting from manufacturing defects that occur while the Product is in the customer’s possession;
4. Unreasonable or unintended use of Product;
5. If the operator has deemed to have been negligent or failed to maintain the plastic trim in the correct manner;
6. Minor conditions such as stains, and scratches;
7. Damage to the coated surface due to improper wash techniques, automatic car washes or incorrect wash tools that may cause abrasion or by third parties not authorized by the Company;
8. Scratches, scuffs, scrapes, chips to the surface;
9. Water spots – water spots are caused by mineral deposits, which if left to dry on the plastics and/or trim or ceramic coating may leave a stain, water spots are not covered;
10. Damage caused by collision, accidental damage, vandalism, fire, hail, flood, surface rust, rail dust, physical damage, paint overspray, or plastic and/or trim manufacturer’ defects, which may be covered under manufactures protection plan;
11. Areas that have not been re-coated after a paint or body repair;
12. Use in non-automotive applications.

Any information or suggestion by the Company with respect to the Products concerning applications, specifications or compliance with codes and standards is provided solely for your convenient reference and are made without any representation as to accuracy or suitability. You must verify and test the suitability of any information with respect to the Products for your specific application.

THE WARRANTIES SET FORTH HEREIN ARE THE ONLY WARRANTIES MADE BY THE COMPANY IN CONNECTION WITH THESE PRODUCTS. THE COMPANY CAN NOT AND DOES NOT MAKE ANY IMPLIED OR EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, AND DISCLAIMS ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PRODUCTS SOLD BY COMPANY ARE SOLD ONLY TO THE SPECIFICATIONS SPECIFICALLY SET FORTH BY COMPANY IN WRITING. OTHER THAN THE LIMITED WARRANTY SET FORTH HEREIN, THE COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY’S SOLE OBLIGATION UNDER THIS WARRANTY SHALL BE REPAIR OR REPLACEMENT OF NON-CONFORMING PRODUCTS, OR AT THE OPTION OF THE COMPANY, RETURN OF THE PRODUCT AND A REFUND OF THE PURCHASE PRICE. BUYER ASSUMES ALL RISK WHATSOEVER AS TO THE RESULT OF THE USE OF THE PRODUCTS PURCHASED, WHETHER USED SINGULARLY OR IN COMBINATION WITH ANY OTHER PRODUCTS OR SUBSTANCES.

Limitation Of Liability

Annual Inspections

Contact Information

09 //

UPHOLSTERY v2

Carpet, fabric, leather and/or vinyl against fading and non-removable staining.

2 YRS

from install date

Transfer:

YES

Annual check:

REQUIRED

XPEL PDF ↗

Limited Product Warranty

FUSION PLUS UPHOLSTERY v2

XPEL, Inc. (the “Company”) expressly warrants to the owner that, for a period of two (2) years (the “Warranty Period”) from the date of initial installation. The Company will cover the vehicles interior surfaces on the FUSION PLUS UPHOLSTERY v2 (the “Product(s)”) such as: carpet, fabric, leather and/or vinyl against fading and non-removable staining. This Limited Warranty only applies to the Company’s Products which are professionally installed in the manner recommended by the Company.

The Company will, at its option, remove or replace the Product without charge, or refund the cost of the Product, if the Product fails or does not perform as warranted solely due to a manufacturing defect within the Warranty Period, subject to the exclusions set forth in this Limited Warranty. If the Company elects to replace the Product, the Company will have an authorized installer of its choice remove and reapply the Product to areas determined by the Company in its sole discretion to be covered by this Limited Warranty. The Company will cover parts and the authorized installer will be responsible for providing installation labor. The refund of the cost of the Product or replacement of the defective coating are the exclusive remedies for all Products covered under this Limited Warranty. During the entire Warranty Period, the Company’s obligation as to repair or replacement shall further be limited to repair or replacement with the Products that are available at the time of the repair or replacement, shall be limited to the repair or replacement of only the specific Product that fails due to a manufacturing defect. The maximum replacement cost to be paid by the Company shall be the lesser of the cost of the coating application or $250. Any repaired or replaced product shall also remain subject to the Warranty Period, and any repair or replacement shall not extend the original Warranty Period in any manner or start a new warranty period. These are the exclusive remedies for all Products covered under this Limited Warranty.

You may obtain coverage under this Limited Warranty by providing Company with proof of warranty card, copy of original receipt for the Product identifying coverage areas, along with a detailed description of the purported defect. For service under this Limited Warranty, you must notify the authorized Company installer who performed the installation of the Product, in writing, providing claimant’s name, phone number, address, and the installation address (if different), a description of the product involved and the nature of the defect.

This Limited Warranty is transferable only when the new owner submits to the Company proof of the original date of installation. Transfer of the Limited Warranty only entitles the new owner coverage for the remainder of the original Warranty Period.

Disclaimer Of Warranties

The Company’s Products must be stored, handled, installed, used, and maintained in accordance with instructions provided by the Company, and this Limited Warranty is conditioned upon compliance with all such instructions. Copies of the Company’s guides are available from the Company at the address listed below. You may also obtain this/these materials by contacting Company at +1-210-678-3700 or on the Company’s website at www.xpel.com/fusion-plus.

This Limited Warranty does not cover defects caused by:

1. Non-compliance with the Company’s guide or instructions. Such failures include, but are not limited to, exposure to physical abuse, including, but not limited to chemical abuse (e.g. harsh cleansers and solvents), thermal abuse or shock (e.g. excessive heat or cold) or misuse;
2. Improper storage, installation, handling and/or use of the Product;
3. Damage not resulting from manufacturing defects that occur while the Product is in the customer’s possession;
4. Unreasonable or unintended use of Product;
5. If the operator has deemed to have been negligent or failed to maintain the carpet, fabric, leather and/or vinyl in the correct manner;
6. Minor conditions such as stains, and scratches;
7. Damage to the coated surface due to improper wash techniques, automatic car washes or incorrect wash tools that may cause abrasion or by third parties not authorized by the Company;
8. Damage to interior surfaces prior to application;
9. Water spots – water spots are caused by mineral deposits, which if left to dry on the interior surface and/or ceramic coating may leave a stain, water spots are not covered;
10. Damage caused by collision, accidental damage, vandalism, fire, hail, flood, physical damage, paint overspray, or carpet, fabric, leather and/or vinyl manufacturer’ defects, which may be covered under manufactures protection plan; and
11. Alcantara and suede fabrics.
12. Areas that have not been re-coated after repair;
13. Use in non-automotive applications.

Any information or suggestion by the Company with respect to the Products concerning applications, specifications or compliance with codes and standards is provided solely for your convenient reference and are made without any representation as to accuracy or suitability. You must verify and test the suitability of any information with respect to the Products for your specific application.

THE WARRANTIES SET FORTH HEREIN ARE THE ONLY WARRANTIES MADE BY THE COMPANY IN CONNECTION WITH THESE PRODUCTS. THE COMPANY CAN NOT AND DOES NOT MAKE ANY IMPLIED OR EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, AND DISCLAIMS ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PRODUCTS SOLD BY COMPANY ARE SOLD ONLY TO THE SPECIFICATIONS SPECIFICALLY SET FORTH BY COMPANY IN WRITING. OTHER THAN THE LIMITED WARRANTY SET FORTH HEREIN, THE COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY’S SOLE OBLIGATION UNDER THIS WARRANTY SHALL BE REPAIR OR REPLACEMENT OF NON-CONFORMING PRODUCTS, OR AT THE OPTION OF THE COMPANY, RETURN OF THE PRODUCT AND A REFUND OF THE PURCHASE PRICE. BUYER ASSUMES ALL RISK WHATSOEVER AS TO THE RESULT OF THE USE OF THE PRODUCTS PURCHASED, WHETHER USED SINGULARLY OR IN COMBINATION WITH ANY OTHER PRODUCTS OR SUBSTANCES.

Limitation Of Liability

Annual Inspections

Annual inspections must be carried out by an XPEL Certified Installer, within thirty (30) days before or after the installation date of the application or last service date. Failure to complete the inspection, within the required time will void the Limited Warranty. Any fees or charges by the XPEL Certified Installer will be charged to the owner to do the annual inspection including, but not limited to, interior detail, vacuum, and inspection. Please keep proof of all inspections, as they must be provided if you have a Limited Warranty related issue.

Contact Information

10 //

MARINE V2

Environmental contaminants, loss of gloss, and UV damage.

3 YRS

from install date

Transfer:

YES

Annual check:

REQUIRED

XPEL PDF ↗

Limited Product Warranty

FUSION PLUS MARINE v2

XPEL, Inc. (the “Company”) expressly warrants to the owner that, for a period of three (3) years (the “Warranty Period”) from the date of initial installation. The Company will cover the recreational watercrafts factory paintwork on the FUSION PLUS MARINE v2 (the “Product(s)”) against: environmental contaminants, loss of gloss, and UV damage. This Limited Warranty only applies to the Company’s Products which are professionally installed in the manner recommended by the Company.

The Company will, at its option, remove or replace the Product without charge, or refund the cost of the Product, if the Product fails or does not perform as warranted solely due to a manufacturing defect within the Warranty Period, subject to the exclusions set forth in this Limited Warranty. If the Company elects to replace the Product, the Company will have an authorized installer of its choice remove and reapply the Product to areas determined by the Company in its sole discretion to be covered by this Limited Warranty. The Company will cover parts and the authorized installer will be responsible for providing installation labor. The refund of the cost of the Product or replacement of the defective coating are the exclusive remedies for all Products covered under this Limited Warranty. During the entire Warranty Period, the Company’s obligation as to repair or replacement shall further be limited to repair or replacement with the Products that are available at the time of the repair or replacement, shall be limited to the repair or replacement of only the specific Product that fails due to a manufacturing defect. The maximum replacement cost to be paid by the Company shall be the lesser of the cost of the coating application or $1000. Any repaired or replaced product shall also remain subject to the Warranty Period, and any repair or replacement shall not extend the original Warranty Period in any manner or start a new warranty period. These are the exclusive remedies for all Products covered under this Limited Warranty.

You may obtain coverage under this Limited Warranty by providing Company with proof of warranty card, copy of original receipt for the Product identifying coverage areas, along with a detailed description of the purported defect. For service under this Limited Warranty, you must notify the authorized Company installer who performed the installation of the Product, in writing, providing claimant’s name, phone number, address, and the installation address (if different), a description of the product involved and the nature of the defect.

This Limited Warranty is transferable only when the new owner submits to the Company proof of the original date of installation. Transfer of the Limited Warranty only entitles the new owner coverage for the remainder of the original Warranty Period.

Disclaimer Of Warranties

The Company’s Products must be stored, handled, installed, used, and maintained in accordance with instructions provided by the Company, and this Limited Warranty is conditioned upon compliance with all such instructions. Copies of the Company’s guides are available from the Company at the address listed below. You may also obtain this/these materials by contacting Company at +1-210-678-3700 or on the Company’s website at www.xpel.com/fusion-plus.

This Limited Warranty does not cover defects caused by:

1. Non-compliance with the Company’s guide or instructions. Such failures include, but are not limited to, exposure to physical abuse, including, but not limited to chemical abuse (e.g. harsh cleansers and solvents), thermal abuse or shock (e.g. excessive heat or cold) or misuse;
2. Improper storage, installation, handling and/or use of the Product;
3. Damage not resulting from manufacturing defects that occur while the Product is in the customer’s possession;
4. Unreasonable or unintended use of Product;
5. Products installed with known or visible manufacturing defects at the time of installation, including, but not limited to failing clear coat, swirl marks, scratches, scuffs, scrapes, chips to the watercraft surface;
6. Minor conditions such as stains, and scratches;
7. Damage to the coated surface due to improper wash techniques, incorrect wash tools that may cause abrasion or by third parties not authorized by the Company;
8. Swirl marks, scratches, scuffs, scrapes, chips to the watercraft surface;
9. Water spots – water spots are caused by mineral deposits, which if left to dry on the watercraft surface and/or ceramic coating may leave a stain, water spots are not covered;
10. Damage caused by collision, accidental damage, vandalism, fire, hail, flood, surface rust, rail dust, physical damage, paint overspray, or marine manufacturer’ defects, which may be covered under manufactures protection plan; and
11. Areas that have not been re-coated after repair or replacement.
12. Commercial and/or rear of fishing boats are not covered.
13. Waterline and areas below the waterline are not covered.
14. Walking areas and fish handling areas are not covered.
15. Use in non-marine applications.

Any information or suggestion by the Company with respect to the Products concerning applications, specifications or compliance with codes and standards is provided solely for your convenient reference and are made without any representation as to accuracy or suitability. You must verify and test the suitability of any information with respect to the Products for your specific application.

THE WARRANTIES SET FORTH HEREIN ARE THE ONLY WARRANTIES MADE BY THE COMPANY IN CONNECTION WITH THESE PRODUCTS. THE COMPANY CAN NOT AND DOES NOT MAKE ANY IMPLIED OR EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, AND DISCLAIMS ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PRODUCTS SOLD BY COMPANY ARE SOLD ONLY TO THE SPECIFICATIONS SPECIFICALLY SET FORTH BY COMPANY IN WRITING. OTHER THAN THE LIMITED WARRANTY SET FORTH HEREIN, THE COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY’S SOLE OBLIGATION UNDER THIS WARRANTY SHALL BE REPAIR OR REPLACEMENT OF NON-CONFORMING PRODUCTS, OR AT THE OPTION OF THE COMPANY, RETURN OF THE PRODUCT AND A REFUND OF THE PURCHASE PRICE. BUYER ASSUMES ALL RISK WHATSOEVER AS TO THE RESULT OF THE USE OF THE PRODUCTS PURCHASED, WHETHER USED SINGULARLY OR IN COMBINATION WITH ANY OTHER PRODUCTS OR SUBSTANCES.

Limitation Of Liability

Annual Inspections

Annual inspections must be carried out by an XPEL Certified Installer, within thirty (30) days before or after the installation date of the application or last service date. Failure to complete the inspection, within the required time will void the Limited Warranty. Any fees or charges by the XPEL Certified Installer will be charged to the owner to do the annual inspection including, but not limited to, exterior wash, decontamination, and inspection and single layer reapplication of coating. Please keep proof of all inspections, as they must be provided if you have a Limited Warranty related issue.

Contact Information

11 //

AIRCRAFT

Environmental contaminants, loss of gloss and UV damage.

2 YRS

from install date

Transfer:

YES

Annual check:

REQUIRED

XPEL PDF ↗

Limited Product Warranty

FUSION PLUS AIRCRAFT

XPEL, Inc. (the “Company”) expressly warrants to the owner that, for a period of two (2) years from the date of initial installation (the “Warranty Period”), the Company will cover the aircraft’s factory paintwork and XPEL paint protection films finish on the FUSION PLUS AIRCRAFT (the “Product(s)”) against: environmental contaminants, loss of gloss and UV damage. This Limited Warranty only applies to the Company’s Products which are professionally installed in the manner recommended by the Company.

The Company will, at its option, remove or replace the Product without charge, or refund the cost of the Product, if the Product fails or does not perform as warranted solely due to a manufacturing defect within the Warranty Period, subject to the exclusions set forth in this Limited Warranty. If the Company elects to replace the Product, the Company will have an authorized installer of its choice remove and reapply the Product to areas determined by the Company in its sole discretion to be covered by this Limited Warranty. The Company will cover parts and the authorized installer will be responsible for providing installation labor. The refund of the cost of the Product or replacement of the defective coating are the exclusive remedies for all Products covered under this Limited Warranty. During the entire Warranty Period, the Company’s obligation as to repair or replacement shall further be limited to repair or replacement with the Products that are available at the time of the repair or replacement, shall be limited to the repair or replacement of only the specific Product that fails due to a manufacturing defect. The maximum replacement cost to be paid by the Company shall be the lesser of the cost of the coating application or $1000. Any repaired or replaced product shall also remain subject to the Warranty Period, and any repair or replacement shall not extend the original Warranty Period in any manner or start a new warranty period. These are the exclusive remedies for all Products covered under this Limited Warranty.

You may obtain coverage under this Limited Warranty by providing Company with proof of warranty card, copy of original receipt for the Product identifying coverage areas, along with a detailed description of the purported defect. For service under this Limited Warranty, you must notify the authorized Company installer who performed the installation of the Product, in writing, providing claimant’s name, phone number, address, and the installation address (if different), a description of the product involved and the nature of the defect.

This Limited Warranty is transferable only when the new owner submits to the Company proof of the original date of installation. Transfer of the Limited Warranty only entitles the new owner coverage for the remainder of the original Warranty Period.

Disclaimer Of Warranties

The Company’s Products must be stored, handled, installed, used, and maintained in accordance with instructions provided by the Company, and this Limited Warranty is conditioned upon compliance with all such instructions. Copies of the Company’s guides are available from the Company at the address listed below. You may also obtain this/these materials by contacting Company at +1 (210) 678-3700 or on the Company’s website at www.xpel.com/fusion-plus.

This Limited Warranty does not cover defects caused by:

1. Non-compliance with the Company’s guide or instructions. Such failures include, but are not limited to, exposure to physical abuse, including, but not limited to chemical abuse (e.g. harsh cleansers and solvents), thermal abuse or shock (e.g. excessive heat or cold) or misuse;
2. Improper storage, installation, handling and/or use of the Product;
3. Damage not resulting from manufacturing defects that occur while the Product is in the customer’s possession;
4. Unreasonable or unintended use of Product;
5. Products installed with known or visible manufacturing defects at the time of installation, including, but not limited to, failing clear coat, swirl marks, scratches, scuffs, scrapes or chips to the aircraft surface;
6. Minor conditions such as stains, and scratches;
7. Damage to the coated surface due to improper wash techniques, incorrect wash tools that may cause abrasion or by third parties not authorized by the Company;
8. Swirl marks, scratches, scuffs, scrapes or chips to the aircraft surface;
9. Water spots – water spots are caused by mineral deposits, which if left to dry on the aircraft surface and/or ceramic coating may leave a stain;
10. Damage caused by collision, accidental damage, vandalism, fire, hail, flood, surface rust, rail dust, physical damage, paint overspray, or aircraft manufacturer’ defects, which may be covered under a manufacturer’s protection plan;
11. Areas that have not been re-coated after a paint or body repair;
12. Salt, salt water/spray or deicing related damage;
13. Areas around exhaust and fueling ports; and
14. Use in commercial aircraft and non-aircraft applications.

Any information or suggestion by the Company with respect to the Products concerning applications, specifications or compliance with codes and standards is provided solely for your convenient reference and are made without any representation as to accuracy or suitability. You must verify and test the suitability of any information with respect to the Products for your specific application.

THE WARRANTIES SET FORTH HEREIN ARE THE ONLY WARRANTIES MADE BY THE COMPANY IN CONNECTION WITH THESE PRODUCTS. THE COMPANY CAN NOT AND DOES NOT MAKE ANY IMPLIED OR EXPRESS WARRANTIES WITH RESPECT TO THE PRODUCT, AND DISCLAIMS ALL OTHER WARRANTIES, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. PRODUCTS SOLD BY COMPANY ARE SOLD ONLY TO THE SPECIFICATIONS SPECIFICALLY SET FORTH BY COMPANY IN WRITING. OTHER THAN THE LIMITED WARRANTY SET FORTH HEREIN, THE COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY’S SOLE OBLIGATION UNDER THIS WARRANTY SHALL BE REPAIR OR REPLACEMENT OF NON-CONFORMING PRODUCTS, OR AT THE OPTION OF THE COMPANY, RETURN OF THE PRODUCT AND A REFUND OF THE PURCHASE PRICE. BUYER ASSUMES ALL RISK WHATSOEVER AS TO THE RESULT OF THE USE OF THE PRODUCTS PURCHASED, WHETHER USED SINGULARLY OR IN COMBINATION WITH ANY OTHER PRODUCTS OR SUBSTANCES.

Limitation Of Liability

Annual Inspections

To maintain the warranty on your product, an annual inspection is required throughout the warranty period, as stated in the product specifications. This inspection should be performed by an XPEL certified Fusion Installer every year and must be completed within 30 days before or after the anniversary date of installation or the date of any previous inspection or service. Failure to complete the inspection, within the required time will void the Limited Warranty. Any fees or charges by the XPEL Certified Installer will be charged to the owner to do the annual inspection including, but not limited to, exterior wash, decontamination, inspection, and a single layer application of XPEL FUSION PLUS AIRCRAFT Ceramic Coating. Please keep proof of all inspections, as they must be provided if you have a Limited Warranty related issue.

Contact Information

// 04 · XPEL WINDSHIELD PROTECTION FILM

WINDSHIELD FILM.

Product · What’s covered

Coverage

Transfer

Annual check

Terms

01 //

WINDSHIELD PROTECTION FILM

Yellowing, cracking, blistering, and delaminating.

1 YR

or 12,000 miles

Transfer:

YES

Annual check:

NOT NEEDED

View / Download PDF

// Book with us

ANNUAL INSPECTION.

If your product’s XPEL warranty terms call for an annual inspection, we can do it.

Book your inspection

QUESTIONS? START WITH US.

We installed it, so we handle the claim with XPEL for you. You can also reach XPEL’s warranty team directly.

XPEL warranty department

711 Broadway St., Ste. 320
San Antonio, TX 78215

(800) 447-9928 xpelwarranty@xpel.com

// Ready when you are

We're ready,
let's talk!

Book Now → Call (337) 345-5860

// Contact

Get a Quote.

// Contact Info

Address

Prestige Films
300 Cardinal Drive
Lafayette, Louisiana 70508

Phone

+1 (337) 345-5860

Opening Hours

Monday

07:00 AM – 05:00 PM

Tuesday

07:00 AM – 05:00 PM

Wednesday

07:00 AM – 05:00 PM

Thursday

07:00 AM – 05:00 PM

Friday

07:00 AM – 11:00 AM

Saturday

Closed

Sunday

Closed